Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hi,
I am trying to run the ble_app_uart_coexist example on my nRF52840 Development board.
I followed the above steps for configuring the example to work.
I copied...
how to include SPI Master code in ble_app_uart sample code of pca 10028(nRF51822) board. its soft device is sdk 10.0.0 (s110). Please share me a sample code if you have. ...
Hello to everyone.
I´m trying to understand a code starting from the file of definition of pins of nRF52 PCA10040. In "simple_hal.c" there's a line like this: NRF_GPIO-...
Hello,
I have consulted the nRF52840 Dongle and cannot get the spec of the PCB antenna.
I need the information for FCC Test. Could someone help me?
Thank you very...
I found lines 766 - 768
CONFIG_GPS_SIM_DEV_NAME="GPS_SIM" CONFIG_GPS_SIM_BASE_LATITUDE=6325280 CONFIG_GPS_SIM_BASE_LONGITUDE=1026201
in \ncs\nrf\samples\nrf9160\asset_tracker...
hi all ,
When implementing an application, the developer has to consider all scenarios that may happen with the IO capabilities of the device.
when my scenarios is My...
Things were working ok yesterday but today I can't open any projects. For some reason now, it fails and says the project file is invalid. Here is the output
Loading solution...
Hi,
My system needs to maintain certain gpio at their state at all times, including when switching to bootloader,
I understand that reset will also return my gpios to...
I'm trying to set up an ESB PRX on an nRF52 that has to communicate with an nRF24L01 chip acting as PTX. Because I want to react to the received data as quickly as possible...
Hello,
I am trying to use Softdevice and the latest Github version of 802.15.4 support. The make (using linux/armgcc) fails on
nrf_raal_softdevice.c
because nrf_802154_radio_irq_handler...
Using SDK 15.2 on an nRF52832 using SoftDevice S132. FDS works OK unless the SoftDevice is enabled. None of the examples work. We've tried the peripheral example, GitHub examples...
Hi,
I'am testing direct advertise and I found strange behaviour with "nrf connect" app.
1. Direct advertises won't be proceeded on "nrf connect" unless there is at least...
Hello everyone
I got back on my bluetooth mesh project after an interruption and at the time I remember having the same compilation problems solved so far.
I worked with...
Hi all,
I acquired the wonderful nRF9160 DevKit which embeds the ARM CryptoCell 310.
Rather than using the mbedTLS or TinyCrypt libs, I would like to rely on the CC310...
hi....
i am just started to program the mesh , i am getting the error in my example code , how to solve ? this is the latest version of 3.1
boards.h: No such file or ...
