I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Dear all,
I defined "DEBUG" , used UART peripheral and "printf()" in the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96. I find nRF52832 always dead in the place at...
Hello,
To determine the current network topology I hoped I could use the heartbeats to determine the RSSI and the number of hops. The RSSI of the last node is in the example...
Hi,
I found this example here for nrf51.
github.com/.../nrf51-ble-gzll-device-uart
And this is more or less what I would need for my application.
Is there a way that...
Hi All,
Scanning with a nRF52840 Dongle, Is there a way to know if one of the scanned devices is using Coded PHY modulation to advertise? And if the answer is negative,...
OS ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board CPU :(Nordic) nRF52832 / ARM Cortex -M4F 32 bit processor 28-pin Land Grid Array / 15GPIOs / SWD Soft Ver:nRF5_SDK_15...
Hi,
I am using "ble_app_uart" code and added battery service to it as custom changes.
I want to update battery level at every 3 seconds.
Code is working fine and starts...
Hi - In the examples provided, a peripheral will go to power off after completing its transactions.This means the the application does not have to "clean up" afterwards. ...
in pca10056.h, there are 4 buttons.
I want to add one new button, //#define BUTTON_5 NRF_GPIO_PIN_MAP(1,06).
However , it failed.
I debug and find the issue, #define...
i used SDK9.0.0 to implement the function that bond to cellphone.
case 1:when i set the IO_CAPABILITIES to BLE_GAP_IO_CAPS_DISPLAY_ONLY,the process of bond is ble device...
Hello,
i m using sdk15.2.0 in nrf52840.
please help for increase adv data size from 31 byte to 45 to 50 bytes..
i had tried with "BLE_GAP_ADV_TYPE_EXTENDED_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED...
RTC connect through I2C and GPS connect to UART. I am getting large amount of data from gps contentiously . In the mean time i should read time from RTC . But i am getting...
i have 2 setups, one on a pca10040 running sdk 14.2.0 s132 and the other one on a pca10028 clone running sdk12.3.0 s130 with a 51822_xxaa mpu
the ble_uart examples from...
I just want a simple and clear PWM driver to generate a duty cycle on a GPIO pin - 25% on and 75% off. Just that. What is the most power efficient method?
The example PWM...
Hi,
Yesterday I installed the image ' RaspPi_OT_Border_Router_Demo_v1.0.0-1.alpha.img' on a Raspi 3B+ and cpnnected a Nrf52840 DK via native USB. Using the 2.0.0 Thread...
