I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
The sdk_config.h configuration file for ble_app_hrs_freertos example contains following definition:
#define NRFX_GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS 1
This macro should...
HI,
I have connected to one peripheral from my central and retrieved all the services(For example i need Device Information Service, got all the characteristic values) and...
dear sir,
i have a nRF52DK board,
i want to power on the board but not glowing LED and my laptop not detect the board while connect with laptop,
please given solution...
Hi
Env: keil and no SD
I am doing the first steps on keil + nordic nrf51822. I started by opening the Blinky app (C:\Keil_v5\ARM\PACK\NordicSemiconductor\nRF_Examples...
Hi there ,
i am developing a biomedical recorder which needs to continuously transmit the recorded data ,
data rate is very low (9.6 Kbit/s to 32Kbit/s) but i have a very...
Hello,
I was wondering whether or not there is a way to know, how the connection interval is decided between the two values of the Connection Interval Max and Connection...
Hi, everyone,
We develop the project by using nRF52822 module. But suddnely we discovered that the latest supporting this chip sdk versionis 12.3. The SDK versions newer...
According the the instructions for the Thingy mesh demo, it is possible to manually provision new nodes. Is it possible to identify the unprovisioned node first by sending...
I am trying to make the nrf52832 enter in ON/low power mode for inactivity periode.
I must have the "System ON, No RAM retention, Wake on RTC" as indicated in nrf52832 datasheet...
Hi,
I run the Secure DFU, and I'm doing OTA update without any issue.
The problem is the case that I'm doing an OTA update with a application-version smaller than...
Hi all, Nordic distributors no longer carry the nRF52840-PDK, which included the NFC antenna. What is a direct replacement for the Nordic NFC antenna that used to be included...
I am trying to connect a BerryMed MD1000 Pulse Oximeter (BLE Server) with an Adafruit Bluefruit Feather (nRF52-enabled) Arduino board (BLE Client).
I made an Arduino sketch...
hi All!
I use WAKE UP event from G-SENSOR on some GPIO to wake up the MCU on motion detected.
But sometimes ( ~1% ) the event does not occur for unknown reason until RESET...
Hi,
I want to have 2 SPI slaves on the same bus.
I saw in other posts that in the past it was not supported by the spi driver and that i should use NRF_DRV_SPI_PIN_NOT_USED...
