I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Hi,
Is there any example of adc (saadc) and uart throw ble?
I want to take same measurements from fotoresistor and send data via ble_uart i found same example but no...
I have a problem in selecting inductor(L1). In NRF52832 IC datasheet, mentioned specifications of inductor L1 are: 3.9nH, 0402 high-frequency chip inductor. What should be...
I am writing a bluetooth mesh application with a server and client.
Provisioning is working, but the configuration of the server is giving me problems.
I have based my...
Above image is our design for nRF51822. Design also contains Accelerometer and WiFi (ESP8266).
My problem is, I am not able to see nRF BLE advertisement while scanning...
Hi!
Can someone please help me debug this example. It used to work, then I changed number of peripheral links to 1 (to see what RAM suggestion would be), then returned it...
Hi!
I try to flash nrf52 from keil and message appear:
The firmware of the connected J-link (S/N: xxxxxxxx) does not support the following memory access: Read @ 0x02000004...
Hello,
I want to enable UART only when data transfer is necessary.
I am using nrf 52832 and sdk 14.0.0.
I am using "ble_app_uart".
I could not find the answer I...
Hello everyone.
I have a question about sleep_mode_enter() behavior.
I'm using nRF5_SDK_12.3.0 and nRF51822 for my project.
I put a lot of printf statements in the example...
Hello All,
I am working two BLE chipset , one is nordic and another one different make (TI) so is it possible to communicate between two different make BLEs using our nordic...
In NRF 51822 custom board I uploaded ble_app_uart code. Program uploaded successfully. But not able to discover from Phone and Tablet, where in another board it works properly...
hello,everyone.we want to use pin3 and pin4 as txd and rxd,but there has error.could you give us some help?
void debug_uart_init(void)
{
uint32_t err_code;
const app_uart_comm_params_t...
hi,
i made my nrf 52840 dk advertise unlimitedly using ble_app_uart example. connected and disconnected several times using nrfconnect app. it really works fine. with this...
Hi,
I'm using nRF52832 and LDETECT mode for GPIOTE PORT event to detect multiple interruption.
Even though LDETECT mode is described in the product sheet page 112 and...
Dear friends, my current measuing instrument is Power Profiler Kit. I have some troubles when i use it. e.g. 1) how to completely stop an updating plot that a PPK draws? even...
Dear friends, 1) As shown in the pic below, there are some values "max:13.70, min:3.33, rms:3.45..." at the bottom of the pic. which area is these values calculated from?...
