hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I'm migrating form S332 0.9.1alpha (aligned to S132 2.0.0) to the newer S332 2.0.1 (aligned to S132 3.0.0) on a nRF52 board, and I'm seeing a new characteristic under Generic...
Hello,
I am trying to configure gpiote to give an interrupt for wake on motion functionality in MPU9250
I am configuring the MPU for that by calling separate wake_on_motion...
I tried to run some examples from pc_ble_driver_py but i always end up with the following exception.
(using python 2.7.9)
Traceback (most recent call last):
File ...
I have an application developed using S110 v7.3.
I want to upgrade to v8.0 to get additional features (over air update, DC/DC converter etc.), but notice S110 is not supported...
I have bootloader that supports Serial(HCI) DFU on the nrf52832 device which I have to update to Bootloader that supports OTA DFU and also a new application firmware. I tried...
Hi,
When trying to update an app using Secure DFU, we get invalid object error. The error comes from dfu_decode_command.
Using nRF5 SDK 12.2.0 on custom nRF51822 board...
I have followed the CoAP example from IoT SDK,
I have a Raspberry PI set up as the router,
and two nRF52 boards, one is the client, the other is the server.
Following...
I have following questions:
Is there an example for implementing WeChat on a nRF52?
Is the nRF52 module supported for WeChat AirSync?
Where can i finde the requirements...
Hello!
I'm drawing a circuit with nrf52840 chip and I want to ask some questions:
Is it ok to use 2-side pcb (not 4)? what's of these better in part of radio communication...
Hi, I use nrf connect to programing demo board nrf51 dongle to get it work, failed.
error log as follows:
2017-03-02T09:30:20.014Z INFO Application data folder: C:\Users...
Hi,
Does the PPI module automatically clear the event flags for the linked event? For example, if I have the following:
NRF_PPI->CH[0].EEP = (uint32_t)&(NRF_GPIOTE->EVENTS_IN...
hi
I'm porting Arduino code which has calls to ShiftIn() to read a byte from a GPIO Pin and bitWrite() to write a bit into a byte variable at a particular position.
Below...
dear friends,
now i need to let a master 52832 device communicate with multiple slave 52832s.how can i make it? Our scenario is that a teacher takes a phone in a classroom...
