Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hello,
So — in just trying to get the blink example working, I've come across all kinds of toolchain weirdness. I'm using CrossWorks, because it's on OSX and it's way cheaper...
Hi all
Is possible from softdevice or from program application edit the GAP service? I know this service is mandatory but what about edit the structure which is shown on...
Please give me a professor.
In the nRF 52832 sample project, there is an NRF_LOG_INFO function, is this the ability to output a debug string to the UART?
If so, how can...
I have custom service, where I have declared 2 handles inside BLE Service structure, one for button action and the other for custom battery ADC measurement, each identified...
Hi,
I have seen similar questions to this, but I could not make it work.
I am trying to upload a new code using DFU by means of a smartphone (using nRF Connect) or PC...
Hi. I just noticed this bombshell in the release notes for v13.0.0-1.alpha:
Dropped support for nRF51 Series devices.
Although this is preceded by:
...
Hello ! I am trying to implement a write request but for unknown reason it doesn't transmit back the gatt_status. I have setup the wr_auth = 1. GPIO number 19 si actually...
Hi, I want to add DFU to ANCS example.
I use SAMSUNG GALAXY Note5, nRFToolbox, SDK 11, nRF52832, softdevice 2.0.1.
Bootloader project I use is : nRF5_SDK_11.0.0_89a8197...
Hello,
I am working on ota ble_secure project. I have created a zip file which is the last step and copied this file to my smart phone so that I can upload it using nrf toolbox...
Apparently you need to set the CCCD handle of your target characteristic to enable notification. Problem is, how do you do that? I now know at least 2 ways to do that, one...
Hello!
I am using application that support ANT+ and BLE, so i am using s332 softdevice.
now I want to add BLE bootloader feature. (send .bin via BLE). but in SDK v12.2.0...
I am using the nrf52 development board, when I try to connect to one of its pins a signal from a sensor that generates an interrupt signal every 1ms the programs stops or...
Hi,
I have relay board which is attached to the SoC module nRF9E5 and also microchip serial SPI EEPROM 25AA320 is also attached.
I have the EEPROM programmer and I am...
