Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
I measured the current drawn by the nRF51822 beacon with its default beacon code. The current was about 1 mA which was same as in another thread
The suggested solution...
We have been manufacturing for a while with the nRF51822, Revision 2, and WLCSP package and build code D0 (D0 is what Nordic recommended me to spec to contract manufacturers...
Hi all,
I have application that read analog level and send the data with connection interval of 10 ms and 0 dBm, how can i calculate the current consumption of BLE? i read...
Hi
I want to use Printf() in the DT2 but it cannot output msg to terminal.
I used hal_uart_config() to config UART TX/RX/Baudrate... in mail.c then
call hal_uart_put_str...
I use S110 V7.1.0,nrf51822 chip,
now I need write and read flash data in BLE mode.
When can I write the flash data at BLE mode?
When can I read the flash data at BLE...
I'm calling the requestData function and lib_aci_close_remote_pipe at the same time.
The lib_aci_close_remote_pipe returns 0x8E command error which means: "Command rejected...
Hello,
I need to store some app configuration on the FLASH and I'd like to use the features of pstorage module.
I don't understand the following thing ...
When the...
Hello,
I am currently using the SDK setup from this URL: embeddedsoftdev.blogspot.de/.../ehal-nrf51.html
In order to use that setup, one must change a line in the file...
Hello,
I downloaded MDK arm from Keil website (keil mvision 5), SDK and MDK pack from nordic download site. After installing SDK, I am not able to find example projects...
Hello,
I have quite a few of setting on my nodes and I want to save some of these permanently. Currently I am using the pstorage module and everything works as expected...
Hello everyone,
i can able to set the static passkey but i would like to know the difference bewteen security key and passkey how can i set security key ? any suggestions...
Good day!
Faced with the problem that I didn't get to run N5 Starter Kit (nRF51422) on maximum speed in Advanced Burst Mode, using ANTware II with ANTUSB-m to read packets...
I read the multi-role project on Github. For time slot part, there's no explicit hfclk start/stop operation along with the radio events, is it possible that sd_radio_session_open...
In the nRF8001 Arduino SDK, there is a " ble_bandwidth_test " example.
It says,
"The bandwidth is measured (sic?) with the nRF UART App in the Apple iOS app store" ...
