Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
we are facing an issue of loading the application written with nRF Connect SDK to the nRF52840 which has nRF5 SDK's secure bootloader. Update process should be performed...
I try to enable APPROTECT by nrfjprog but seems not work, I still can read the memory after device (PCA10090) reset.
Here is the commands I test to enable APPROTECT
...
I was trying to update the PPK II software, but I am receiving a error message: "Error: EPERM: operation not permitted, mkdir 'D:\'"
Well, in my Windows environment, the...
Hi,
We have been using the DeviKit for our initial development and now we have developed our own custom board using the nRF5340. I trying to flash the device, but couldn...
Hi, We noticed that if you do not "Disconnect" a SEGGER RTT connection (on the RTT Viewer), the nRF52832 chip latches into using a relatively large amount of power (~3mA)...
I'm running the latest nRF Connect under VS Code on Windows 11.
What used to compile and not show errors (a couple weeks ago, and running 2.6.0) is now showing errors on...
I am having a problem where the UART is getting noise and bad data (I assume framing errors too) with Zephyr drivers. I was wondering how in Zephyr do you check for framing...
Hello,
This demo gives me automatic pairing and password input.
https://devzone.nordicsemi.com/f/nordic-q-a/44658/communication-problems-between-ble_peripheral-and-ble_central...
This question is in lieu of an issue on the repository, because I don't think issues are accepted there?
I noticed I was getting the following CMake Warning:
Could not...
I am running on demo "nrf-knx-iot/samples/light_switch_sensor".
I built the demo and burned it into my nrf52840dk successfully, but I could not see more logs.
I found...
Hello! We recently acquired a Nordic Thingy:91 for prototyping and it was working great until I came into work this morning and it was no longer showing any signs of life...
Hi Support team,
When I compile the application on the network core of nRF5340, the result is like below:
There is a 64KB SRAM1 with usage 0%, could you tell me what is...
Issue: No Interrupt Signal on GPIO0 Pin of MAX30208 Sensor with Xiao BLE nRF52840 Using Zephyr NCS v2.6.1
I was write a code for max302078 sensor driver but in this i want...
In some examples that use nrfx libraries it is necessary to extract a GPIO PSEL, which is usually done like this. Give the following DT definitions
``` leds {
compatible...
Hello. I am developing a product equipped with BLE communication function using nRF52480. I am experiencing an issue where the BLE connection cannot be completed.
[Environment...
