Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
Hi I've just started developing with the nrf52840 and Ive been following the official documentation on how to use the programmer shipped with nRF Connect.
Unfortunately...
Hi,
In a custom nrf52840 board (DC/DC=on, LFCLK=RC, CONFIG_SERIAL=n), using ncs2.1.0, I measure through PPKII ~6.7uA in system_off mode, which is reasonable.
In system_on...
I have a similar question as in the previous post (about 4 years ago) with title "nRF52 WLCSP DCC routing - - ok to run over GPIO pins?" by Laserdan, i.e., I would like to...
Hi there,
The spec for nRF52840 says in sec 6.33.1 that for UART, "The external crystal oscillator must be enabled to obtain sufficient clock accuracy for stable communication...
Hi,
How do you export your project from nRF Connect within VSC? You may have modifications you did for DTS files, prj.conf etc, that you may miss if you focus on just src...
Hello,
The documentation for the nRF5340 says that the UICR OTP registers can only be written to a non-0xFFFF value a single time: > Can only be written to a non 0xFFFF...
HI,
In our application, there is strange dependency for BLE service. The device is getting detected on ble scan only if we flash the ble application after flashing an application...
Hello,
with iOS 16 the connection during the update of the Firmware with IOS-DFU-Library not working. It is stop after few second with the error 202.
Do you know any solutions...
Hi, I restart advertising with ble_advertising_start and sd_ble_gap_adv_stop because I need to change the advertising interval in different situations. I am observing high...
I use nRF Connect for Desktop v3.12.0 (the latest) and its apps:
Bluetooth Low Energy (the latest standalone application v4.0.0)
Programmer v3.0.4 (the latest)
Can...
Is there support now for coded phy on nrf ble sniffer?
I'm using the nrf52840 devkit (hardware version 2.0.2 which supports coded phy) and sniffer works fine without coded...
It looks like the BT Mech spec has not been updated since 2017. Is there an update in progress and is Instaburst (or similar function) a candidate feature?
This would seem...
Hi,
I am facing a peculiar problem, wherein my application has two threads as in below:
Thread-1: is a preemptive thread which has UART functionality, along with UART...
I'm trying to run uart secured bootloader example in folder: @NRF5_SDK\examples\dfu\secure_bootloader\pca10040_uart_debug
but it doesn't work.
My setting is:
base...
