Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Is there any characterization for the nPM1304 (or any in the series) with a charging input voltage in the 3.5-4.0 range? I have a ~4V power source, but depending on load it...
Hi,
I'm developing a project that requires to write GPS data to an SD card. I'm using Nordic SD card library.
I'm able to initialize and interact with the SD card only...
Hi there,
I am trying to send large data files via BLE notifications. My setup is nRF5340 development kit sending data to connecting devices (phone, PC).
I have gone through...
System description
I have an nrF54L15 mounted with an external 4 Mbit External flash with FATFS configured
Filesytem config:
# FatFS File system
CONFIG_FILE_SYSTEM...
Hi
About nPM1300
We will use load switch to drive haptic function and its peak current may up to 0.4A~0.5A@25us duration,
I see the spec show the load switch with maximum...
Hi,
I'm running an app on nRF52840 (NCS3.02) based on the BT shell example.
I did the following modifications:
- shell runs on USB-CDC instead of UART
- using NRFX...
While checking the Channel Sounding samples, I came across the concept of Channel Sounding Security Levels . I have a few questions regarding how this is handled in Nordic...
Hi,
I was wondering whether the nrf54H20 can utilise the BLE sniffing firmware used with the nrf52840?
If not, will this firmware be made available in the future and if...
I have a project that was built with SDK and toolchains 1.7.1. This firmware is used in a fielded product. I can't upgrade it to a newer version of the SDK without having...
I am currently using the nRF54L15 DK board along with an external host to develop Channel Sounding functionality. After reviewing related support tickets, I understand that...
I tried updating my project from NCS 3.0.2 to 3.1.0, but it hardfaults at boot. Doesn't log anything to RTT. The warnings/errors at boot in the screenshot can be ignored,...
Hi everyone,
I’m working with the nRF54L05 MCU (SDK v2.9.0) for my application.
From the documentation, I read that in the system_off demo, when using the z_nrf_grtc_wakeup_prepare...
Hello,
I am working on nRF9160 custom board. Since I am reprogramming a lot, this issue is kind of getting on my nerves. Here is the issue:
Usually modem takes couple...
Hello! I purchased some nRF54L15-DK 0_9_3 boards. Recently, I have been conducting relevant tests on the nRF54L15-DK 0_9_3. I want to test the low power consumption performance...
Hi, I am using an external host with NRF54l!5 dk to test the channel sounding feature.
Can you tell me how the NRF controller supports this Cs procedure and whether the...
