Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
i am using mpu 9250 and and using https://github.com/Martinsbl/nrf5-mpu-examples this examples.
the question is can i use magnetometer on spi protocol?
because i have...
1. When I use NRF52832 as the ANCS client to get the notification attributes, if the data exceeds the size of a packet and requires multiple packet transfers, is it the BLE_GATTC_EVT_HVX...
Hello, I am working on a project which requires using FreeRTOS with the nrf9160. Setup: - Boards tested on:actinius icarus, Thingy91) - VS-Code with Ceedling as build tool...
Hi, I have implemented OTA DFU on Android with your official DFU library. We want the DFU to happen in background at a certain trigger (car driving, triggered from device...
Dear Members,
How can I connect via ANT+ to Garmin GSC10 ?
then display cadence and speed value in UART ?
Is it related with this function in ant_bsc_rx_d52_s212.uvprojx...
Hi
My problem is very simple but I don´t know how fix it.
I have a project in my work and it goes very well, but when I returned home,I have build It and it goes with...
Hello,
I'm having an issue with my nrf52832 with and ICM20948 IMU attached. My issue is related to wake up on motion. I believe I've set it right but I can't make it work...
Hi.
I have several issues when trying to respond to Direct Methods (using v1.4.0 of the SDK):
In azure_iot_hub.c:
evt.data.method.rid = atoi(topic->prop_bag[0].value...
Hi !
I am working with a NRF52832 and with SDK 15.2.
For my application, I need sometimes to deactivate the Softdevice to begin some radio tests.
So I have programmed...
I am doing the procedure described in the nRF52840 specification, figure 193 "UARTE reception with forced stop via STOPRX".
I am using 1Mbps with hardware flow control....
I'm testing out the Thingy91 Asset Tracking Application, but I notice when I poll the Accelerometer, I only get junk data back. +/-20m/s^2 on all axis. I'd test this application...
Hi! This is the first time that I develop a BLE system with this MCU, I want to know if it is necessary to install so many vias making a shield around the entire pcb. If so...
Hi,
i'm using SDK11 with NRF52832
After a pin falls from HIGH to LOW The GPIOTE_IRQHandler calls a function in my program to read 8 bits from the bus (Inside the interrupt...
Following the seminar today I tried to build and run this example.
built on command line using west (non-secure nrf9160-DK target)
in a continuous loop I get
```
SPM...
