Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Went through the pin_change_int example and of course it works fine.
Migrated that to custom board and it also worked fine with main loop.
So I then tried to use that...
Have an application that configures a wifi SOC using spim before enabling BLE scanner.
When it is running there are 4 timer events running and the main loop check status...
Hello,
Zephyr 1.14.0 includes the nrfx code to use GPIOTE and PPI and my code compiles but I get
undefined reference errors to the nrfx_gpiote_ and nrfx_ppi_ functions...
Few issues I'm facing -
1. I have gone through the related blogs, tutorial, documentation for DFU. nRFConnect cannot connect to the Fanstel BM832 chip. It gives me an error...
hi
I connect AT24C02 EEPROM with nrf52dk.
I already test EEPROM with arduino and it work fine.
Now i want to communicate with NRF52DK kit,so which example I would prefer...
Hi Nordic.
I have an issue that I'm really stuck on. I am trying to send data from a radar sensor via your nRF52 DK BLE board. I've managed to make a working connection...
Hello,
we would like to use a nRF52DK for a simple bluetooth production testing as mentioned in AN34. If we are using an external 50R antenna on J1 do we need to cut the...
I am using nRF52832 SDK 15.2.
I would like to avoid using the 32.768kHz oscillator to save space and cost.
I am using BLE and sleep mode ON.
I defined in sdk_config...
If I build/flash from the command line with "west build -b nrf9160_pca10090ns" and "west flash -d build" it loads a fully combined image with mcuboot and (spm+application...
I am trying to write a program in C to have my central device(nRF52840 dongle) read the RSSI from a peripheral. I have never written C code before and was told to use:
TASKS_RSSISTART...
Hello, I am using nrf52832. My BLE device is slave device and its sending notification to master. I want to know if there is any feature to know if notification from particular...
Hi,
I am trying to read signal strength inside my code. At the moment I know I can do this with AT commands:
AT+CESQ +CESQ: 99,99,255,255,255, 46 OK
RSRP = -140 + 46...
Hi,
I am trying to develop a high speed application using the nRF51822 chipset. As part of my application, I need to send at least 125 HID IN reports (each 20 bytes long...
Hello Nordic,
I'm developing app with nrf52840, SDK15.3.0 and s340.
The work almost has done, so we need to test ourdoor.
The problem is that we don't find out the...
