Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
I am working on a custom board with the 52840 chip. The problem I'm facing is that when I plug in my custom board, Windows 10 immediately shows a USB malfunction error...
Before my 52840 acting as central is connecting, it scans with the following params list:
static ble_gap_scan_params_t const m_scan_params = { #ifdef BOARD_PCA10056 .extended...
Hi i am using nrf52840 DK and i am trying out sleep_mode after timeout happens. but i had a doubt in ble_adv_evt_idle i.e if i use this case the device goes into sleep and...
Dear all,
I have a problem.The DFU could not be performed due to a large size of the application around 300kB.
Platform : 52832;
SDK: SDK_11.0.0;
softdevice:s132.
If we edit the example code in seggar embedded, are the same changes done for the hex files of the same examples? IF not how do we change the code and put it in the dongle...
Hi,
I was following the instructions laid out in the "Configuring DFU over Mesh" guide in the nRF5 SDK for Mesh v3.1.0 ( https://infocenter.nordicsemi.com/topic/com.nordic...
Hello All,
I am working on nRF51822 custom board and i am not change it because it is customer requirement. Use IAR embedded workbanch IDE in windows 7. For reference...
This post mentions that only logical address 0 is supported for the coded PHY.
Is there any additional explanation for why this is? The OPS does not mention this.
...
Hello, I am working on a project based on a central/peripheral NUS application, with nRF51822 and SDK 12.3 .
I Want to know if the debit of data exchanging is lower when...
Hello,
I have configured the toolchain and SDK by following the NRF Connect getting started guide and followed the below steps to compile the mqtt_simple application (on...
Hi,
i m using central and peripheral code in SDK15.3 version,and i am not able to send or receive more than 20 bytes at a time in nRF52840 chipset.We are using Master...
Hi,
mbedtls is present inside zephyr/ext/lib/crypto but I cannot seem to build/link to it using Nordic's ecosystem. I haven't found a way using prj.conf to access it. Is...
This is my environment.
SDK: 15.2
IDE: Segger Embedded Studio
Platform: OSX
SoC: nRF52832
I am trying to transmit more than 8192 data using TWI.
But in fact...
I get the below linker error.
Error[Lt009]: Inconsistent wchar_t size nrf_cc310_bl_ecdsa_verify_secp256r1.c.obj(libnrf_cc310_bl_0.9.12.a) and 9 other objects in libnrf_cc310_bl_0...
Hello,
I am experimenting with the Flash Device Storage (FDS) API. Specifically, I'm using the nfc_writable_ndef_msg project as a starting point. It's a really good example...
