Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hello Everyone,
I am newbie to nordic BLE environment. This maybe a silly question.
Currently I am using nrf51 DK with SDK11, S130.
Data to be sent through SPI:
...
Hi,
I was trying to add generic onoff server model to the dimming server example in order to On/OFF and Dim the LED on the nRF52 Dev board using nRF Mesh App. I added all...
With 100 battery powered bluetooth long range slave nodes connected to one master. To increase battery lifetime, Is is best to connect/disconnect all slave nodes to the master...
Hello,
I have the following scenario:
The device boots and starts to advertise.
When the central (android phone or iPhone) connects, peripheral requests bonding and...
I am using sdk 11, s130, nrf 51822.
Before getting into the question I ask in the title, I would like to ask this first:
1. Is it correct that every time I call pm_peer_delete_all...
I'm trying to integrate buttonless DFU in BLE app uart example. I added the file: ble_dfu.c, ble_dfu_bonded.c, ble_dfu_unbonded.c in the project. I added the following folder...
It's battery operation so I want to know how to setup 1sec timer and goto sleep_mode(power_down) after 1sec beacon scanning.
I'm using WDT to setup 60sec WDT reset so I...
Hi,
May I know what is the hardware layout for measuring external voltage using SAADC? I may not be understanding the infocenter or the datasheet for setting the external...
In the `Serial Interface`, the `Bluetooth Mesh Packet Send` command does allow specifying the `Time To Live` (TTL) for arbitrary packets, but there is no field for `Retransmit...
Hello, I have a question.
1. When ancs is reconnected, the machine will be reset, and the software will catch the log as follows.
As long as there are a large number of...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
I would like to know what would happen in the following situation.
During central and peripheral...
I noticed that in SDK SES projects, the linker file is generated every time the project is build. However, there is no memory map file specified, only a section placement...
I program in nrf52840 using thingy sdk
I succeeded in receiving the motion service.
The output speed of some motion services is too fast. such as raw, heading, gravity...
Greetings!
I'm new in the Nordic Dev Zone, so I apologize if this has been asked before. I just wasn't able to find a satisfying answer.
I read in this foruns that there...
