I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
Hello,
I am evaluating the module MBN52832 from Murata (Using the development kit). I have installed nRF Connect v2.3 and I have installed and launched Bluetooth Low Energy...
Hi,
In this topic , i was asking about how to increase range in mesh networks. I did some outdoors tests (clear field), changing power (-40, +4, +8 dBm) and mode (1MB and...
I am using nrf52832 to develop based on SDK14.2. I have defined a custom service . There are 7 characteristic in this service. The attribute of each characteristic is set...
When broadcasting mesh messages I use the access_reliable_t struct to set data.
I need clarification on what the contents indicate. The documentation is sparse and doesn...
I'm trying to model up current consumption of our system. I'm looking to put the nRF52840 into System OFF, no RAM, Normal voltage mode and waking up on both GPIO and USB Detect...
Hi,
Is there a list of the exact part numbers for all the components used in the nRF52832 reference designs? I could only find a pretty general Bill of Materials in the...
I am planning to make a custom board using nrf52832 ,for that i need to know what are all the steps need to be followed to perform OTA DFU to upload a custom firmware . List...
Hi everyone.
I'm working with light switch example in MESH SDK 2.0.1.
I want to provisioner working like a client. Provisioner can send command to another node to on/off...
I have to implement temperature sensor readings continuously through interrupts instead of busy waiting example in SDK in order to notify those values over BLE to cloud. ...
I'm looking to encode and decode an AFSK signal (via wire not RF) using 2KHz (0) & 4KHz (1) with an 8-bit frame size and 6 frames to a block. Is this achievable with the Micro...
hello sir i am designing a custom pcb based on your mcu nrf52832 board
can you help me how to customize it according to my need without disturbing antenna .
USB device don't recognized by system if we try to use more than one endpoint in app_usbd_hid_generic library:
APP_USBD_HID_GENERIC_GLOBAL_DEF(m_app_hid, INTERFACE_NUMBER...
Hello Nordic
I'm using nRF5_SDK_15.0.0_a53641a.
I think I found a bug with the ble_nus.c, line: 96
I think the rx_handles.cccd_handle should be the tx_handles.cccd_handle...
Dear all,
I'm trying to run nimble stack with Nuttx OS on nrf52832(pca10040) reference board. Now , most function is working , but it is not stable .
Sometime , the svc...
Hi,
This function is called after I turn on Bluetooth a while of my project.
What is the cause of this and How can I do to fix it? I can't debug to source code of softdevice...
