hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hi,
I am using nRF51822 chip.
I am using the softdevice s120_nrf51_2.1.0. On top of that i am flashing the HRM central example given in the SDK nRF51_SDK_8.1.0_b6ed55f...
Hello, I'm fairly new are Nordic and have inherited a good project from a departing coworker. We are using Keil uVision 5+nRF51822+BLES110 softdevice.
She explained her...
Hello,
As mentioned title, when using printf with softdevice, "Stopped by a vector catch" occurred.
I am using my custom board(nRF51822 and s110).
And I am using IAR...
Hello,
When i try to set value of the gpregret using sd_power_gpregret_set and clear functions in on_write callback function, cpu gets stuck (i check it in debug mode). Can...
Hello
I'm trying to communicate with an sensor over the TWI HW interface during a BLE connection with the S110 soft-device, and every time I try to use the TWI bus the...
Greetings,
There is a bit of strange operation in UARTE peripheral in nrf52832 with the DK. In the simple code below, if both of the if statements with comments 'Check 1...
Hello everyone,
I have a strange issue with s110 + whitelisting + Device Manager + nrf51822 + GCC and hopefully you can help me with a good advice. It appears that the...
hi,
I am trying to integrate buttonless switch to boot loader as explained in the documentation and the hrs experimental example.
I am working on SDK7.2.0 and using...
Hello,
I installed the new nrfjprog but it fails to write my nrf51 dongle:
ERROR: nrfjprog failed for an unknown reason. Run the same command again with
ERROR: argument...
Hi All,
I would like to design a wireless system using nRF51822 with an effective range >100m LoS and 5m under water.The system is used as a ON-OFF control device powered...
I am trying to run an Arduino sketch using the RedBearLab nRF51822. The sketch is designed to transfer data to and from a microprocessor and an Android device via bluetooth...
I'm currently want to use the NVM with ble device, when I tried to send values from the mobile app to be stored to the NVM, it doesn't work, I guessed that the problem that...
I want to write a device ID to the UICR registers at the same time as I flash the app code. I don't use Keil or that nrfproj.exe thing, I'm on a Mac. I have these targets...
