Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I change the example ant_broadcast to acknowledge mode, but it seems that without a peripheral side,the LED0 will still twinkle.I don't know how to change the project...
Hi,
I'm porting a nrf51822 evaluation board 10001 tested application to a custom board. Part of the application is using UART interrupts to raise a flag and start data...
I am experiencing an error in the final linking stage of my build.
_build/blinky_gcc_xxaa_s120_xxaa.bin: file not recognized: File format not recognized
collect2.exe...
Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
My application seems to be running out of memory, now I received NRF_ERROR_NO_MEM from sd_ble_gap_ppcsp_set. I don't understand why this has started since I don't think i...
Im using custom board with nRF8001. I'm using Hello World example from GitHub.
The nrf chip revision is C not D. When I connect the board to Arduino Leonardo the device start...
Hi
I ran the example " ble_app_hrs ". the consumption is 1.5mA, when I hold SWCLK and nRESET low,the consumption is fall to 0.9mA. how I could reduce the consumpion??
I can input "hello" in win8.1 with button 0
==
before text in iphone5
I change
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(16, UNIT_1_25_MS)
#define MAX_CONN_INTERVAL...
Hello,
I am searching for an exampleproject to learn how to connect to motherboards (or an evaluation board)
over bluetooth:
I try to send data from on chip (nrf51822...
It seems that is not possible to rewrite data on a block ?
I want to persist some data. The first time (after erasing all the flash memory) I store a data on a block, it...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Hi all,
I noticed that there are some instructions for testing keyboard on win8.1 or USB dongle.
Can I test it on my iPhone5s which is iOS7.0.4 now?
Regards,
Aaro...
when I use nRF51822 ESB Protocol,I set retransmit delay = 600us,anything else is working
good,communication is very well,but the minimal Tx period is 1.2ms,not 600us,why...
