Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hi,
In a custom nrf52840 board (DC/DC=on, LFCLK=RC, CONFIG_SERIAL=n), using ncs2.1.0, I measure through PPKII ~6.7uA in system_off mode, which is reasonable.
In system_on...
I have a similar question as in the previous post (about 4 years ago) with title "nRF52 WLCSP DCC routing - - ok to run over GPIO pins?" by Laserdan, i.e., I would like to...
Hi there,
The spec for nRF52840 says in sec 6.33.1 that for UART, "The external crystal oscillator must be enabled to obtain sufficient clock accuracy for stable communication...
Hi,
How do you export your project from nRF Connect within VSC? You may have modifications you did for DTS files, prj.conf etc, that you may miss if you focus on just src...
Hello,
The documentation for the nRF5340 says that the UICR OTP registers can only be written to a non-0xFFFF value a single time: > Can only be written to a non 0xFFFF...
HI,
In our application, there is strange dependency for BLE service. The device is getting detected on ble scan only if we flash the ble application after flashing an application...
Hello,
with iOS 16 the connection during the update of the Firmware with IOS-DFU-Library not working. It is stop after few second with the error 202.
Do you know any solutions...
Hi, I restart advertising with ble_advertising_start and sd_ble_gap_adv_stop because I need to change the advertising interval in different situations. I am observing high...
I use nRF Connect for Desktop v3.12.0 (the latest) and its apps:
Bluetooth Low Energy (the latest standalone application v4.0.0)
Programmer v3.0.4 (the latest)
Can...
Is there support now for coded phy on nrf ble sniffer?
I'm using the nrf52840 devkit (hardware version 2.0.2 which supports coded phy) and sniffer works fine without coded...
It looks like the BT Mech spec has not been updated since 2017. Is there an update in progress and is Instaburst (or similar function) a candidate feature?
This would seem...
Hi,
I am facing a peculiar problem, wherein my application has two threads as in below:
Thread-1: is a preemptive thread which has UART functionality, along with UART...
I'm trying to run uart secured bootloader example in folder: @NRF5_SDK\examples\dfu\secure_bootloader\pca10040_uart_debug
but it doesn't work.
My setting is:
base...
Hi all!
I have created a simple application that only turns on a led and power it off using BLE in NRF52810. The thing is that simple app uses a huge RAM (~85%) and flash...
