The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi, I'm using nRF52 DK (nRF52832), demo code <TWI sensor>. I'm using this slave sensor to communicate with Master nRF52 DK. My code gets stuck at sensor_set_mode() function...
Hi,
I am trying to test the eligibility of updating my project from SDK 16.0 to 17.2 using DFU. I programmed just softdevice and bootloader of SDK 16.0 and made a package...
Hello All ,
I want to use timer 2 of nRF52810..my code is not giving any error but timer is also not going to IRQ handler...but if i made the same changes for timer 0 it...
Hello,
I'm using Seeger Embedded Studio and S132.
I'm trying to include ble_nus.h to ble_app template and compiling. But it gives this error:
2> In file included from...
hi,
I have following setup test cases .
Case 1 DK2 , DK1 Initialized with CLI directly
1a DK2 , DK1 Directly connected to CLI Every Thing Works
1b DK2-to-DK1-to-CLI...
Hi,
I am checking the voltage range on the input pins of the Nrf52832. The specs show VIH is 0,7*VDD and VIL is 0,3*VDD. I'm using the Nrf52DK, which has about 2.8V VDD...
Hello again,
This time I am trying to read HID reports using bluetooth to get the state of the caps lock.
I know this should be super simple and its explained in the hid...
Hello, dear developers!
Tell me the solution to the problem, how to properly initialize the SPI peripherals so that the program does not hang while waiting for the end of...
Dear All,
I'm using nrf52840-DK for development purpose of IEEE 802.15.4 standard. One is used as transmitter, while other as receiver. I'm using nrf_radio_driver inside...
Hi, I found that there is a BLE_HCI_DIFFERENT_TRANSACTION_COLLISION when I use nRF52832 in secure connections. The connection would disappear in 32 secs, but there won't be...
There's a Bluetooth mesh sensor server, which realize, for example:
present ambient temperature property and
desired ambient temperature property.
A Bluetooth mesh...
Good morning,
I'm trying to port the HTS to the PCA0056 board towards chip nRF52833.
I followed the guideline and modified memory mapping as follows:
Section Placement...
Hi.
I'm currently trying to scan non-connectable advertisement for continuously.
So, I'm going to set the value of scan window and scan interval same.
For that purpose...
I wants to use break point in project but when i set break point then 4 or 5 times working after that goes to NRF_BREAKPOINT_COND, I am using nRF52832. so guide me where is...
Hi,
I am trying to setup the serial UART DFU process for a custom board. I am able to build and program a combined firmware hex file which includes - Softdevice S140 ...
