Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello there,
We are a test lab based in Leatherhead UK, and would like to use your nRF52840-DK for setting up a test jig to communicate with a DUT(Device Under Test) ...
Hello,
I am trying to determine whether or not the SPI EasyDMA functionality of the nrf52840 supports double buffering in the sense that the DMA controller will switch buffers...
Hello, I have a problem with properly adding the Azure IoT SDK (C) into Segger IDE. Anyone already managed to get through that? My goal is to have Azure IoT Hub working with...
Hi, I'm attempting to use the nRF52832 Smart Remote 3 SDK for a project on an nRF52832. I wish to add Serial Output capability (for debugging purposes). I followed the example...
Hi,
I notice that inside the MESH SDK, "Friend" is actual a hex file from zephyr, which I cannot modify. My goal is to set a "Friend" to connect more than 1 LPN (low power...
Hello, community. I have a question about hardware and software setting for using 32Mhz.
(1) Software setting in sdk_config.h
#ifndef CLOCK_ENABLED #define CLOCK_ENABLED...
Hi, I'm searching a example project to do the qualifications test for my product. I'm using SDK 10, have you an example for this SDK? (in your site I found an example with...
Hello
I'm trying to maximize the throughput between a NRF52832 and iOS devices in both directions.
Currently, I seem to achieve about 400 Kbps from an iPhone 8 to the...
Hello, I Have been using your app Connection for Mobile to test my Heart Rate Monitor BLE, I am using also an Honor 9 Lite (Lineage OS 15.1).
The app Nrf find my monitor...
I would like to use the beacon example to send some manufacturer specific data over BLE.
I am using the nrf52DK , nRF5_SDK_14.2.0_17b948a and s132.
My question is other...
What's the fastest scanning settings for connecting to anywhere from 1 to 20 peripherals at a time? My peripherals are all advertising at 211.25ms. I won't be sending any...
Hi,
I am trying to use an SAADC converter to measure voltage in range from 0v to 3v5 but I cannot succeed. It is not possible to measure a voltage above 3V1. Well at least...
Hello, community.
I'm using NRF51822 SoC(256KB ROM, 32KB RAM) with S130 Softdevice.
I'd like to reduce the rom size and the ram size to decrease the production cost. ...
Hello,
I am using nRF52840 DK for bulding a bluetooth mesh. I would like to use JLink in board kit to flash and debug for other nrf chip.
How I can connect and configure...
Hi,
I'm using SDK 15.3. How do I connect a central (nrf53832) to another central (phone/laptop) using multilink central example? Its only connecting to other peripherals...
