Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
I would like to design a BLE-controlled electronic device. My requirements are:
1- Very low power consumption. (Less than 200uA in IDLE mode)
2- Slow periodic BLE advertising...
We are a module manufacturer and have used the 52810 as a serial port transparent transmission module.
1. Our customer reports that when we put "More service uuid" into...
Hello there,
We're developing a chip with a nRF52840 as the only processor, which we're trying to get certified against 802.15.4. However, we had problems passing the radiated...
Hi,
I made a PCB with nrf52832. In the intial bring up, I noticed its 32MHz XTAL is not up. Then I debugged the PCB and measured the voltages at different points in the...
I have a fairly extensive application built in 12.3.
To add FDS to this I started with 14.2, replaced the logging with RTT and I know I'll have the change the FDS calls...
Hello everyone,
This is my first question ever, sorry voor my bad english.
Im just started to work with a STMF429I discovery board and a NRF52832(isp1507) BLE chip.
Im...
HI nordic
i installed command line tools in https://www.nordicsemi.com/Software-and-Tools/Development-Tools/nRF5-Command-Line-Tools
and i got this exe file nRF5x-Command...
We have a custom board built around the nrf52840 chipset. We developed code against the dk kit of the same now we are trying to get this working on the custom board.
1)...
Hello,
So I need to connect my NRF52 with a LoRa module E32 via an UART connexion, and then I need to send data using this function:
The probleme is that my code work...
Hi!
I have found the following piece of code on an example from a Nordic employee. I'm curious as to its purpose.
Why is the register set, and then read just after...
I am testing BLE 5 throughput with the following hardware and firmware:
- two newly purchased nRF52840 DK boards, one as host and the other as peripheral.
- latest nRF5...
Hello,
I'm looking through the available packages in the SES Package Manager and I came across the captioned package - currently showing version 1.06 (no date). I haven...
...\sdk\nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac\examples\multiprotocol\benchmark\zigbee
IDE: Segger Embedded Studio.
HW: Two 52840 DK, name them : A & B
PC Cli...
