hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello,
Is there a DFU android/IOS library version for my custom app made on C++ available ? I need to implement my own DFU on both android and IOS.
I'm developping with...
Hi
I have made beacon using nrf52 dk
when i measuring power consumption after upoading firmware without removing power it minimum power consumption is 12ua when not...
Hi,
I’m currently trying to design my own pcb based on nRF52 Development Board. I went through a number of pcb files and all of them are associated withnrf52832 without...
i use the keyboard project, bond and pair the iphone7(ios11.2), the iphone display is connected,ok, then i reset the keyboard and erase bonds, the iphone display disconnected...
Hi Dev Zone,
I am attempting to flash a blink led app, based on Zephyr (nrf52_pca10040), to the primo core (contains Nrf52832), through Jlink debugger on a Linux machine...
At what voltage should DCDC be manually turned off for a nRF52832 ?
This thread for nRF51 says:
You must manually disable the DCDC when supply voltage goes below...
Hello,
I followed the steps mentionned in this blog
I did all the required step but I'm still seeing the same behavior.
below is my setup :
I'm using nRF52840 and...
Hi folks,
We got a weird behaviour with our nrf51822(SDK 12.2.0, s130) device. we have built a low power application with following parameters:
MIN_CONN_INTERVAL...
I have tried to understand how data was send from two BLE device. I have had 2 PCA10056 board and I have loaded ble_app_blinky example and ble_app_blinky_c example for each...
Hi All.
I have one question.
I just want to send "volume down key" simplely after connect with android device to take a picture.
I have no idea. and I don't understand...
I modify nrf51 nus in SDK12.3.0 to realize my application, I found when enable uart, the consumption near 830uA , and then call app_uart_close(), the consumption near 5uA;...
Hi,
Is there and C/C++ source code to get float value from 32-bit ieee-11073 FLOAT data type
I need c/c++ code to parse 32-bit ieee-11073 FLOAT data coming from FORA...
Hello,
Using Spi bus with frequency = 4Mbps give me this deformed signals (clock and miso) and when I push it to 8 Mbps I am not able to get the correct values.
Obviously...
When an event is bound to the ppi channel, and this channel is bound to both task_capture and task_clear
can I get the correct COUNT value when an event occurs?
Or can...
Hi all,
I wanna build a IOT gateway. I follow this steps infocenter.nordicsemi.com/index.jsp
When I access coap://[ipv6] It dont have resource light, just only have...
