Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi i have to use this accelerometer and connect it through i2c
www.analog.com/.../EVAL-ADXL345Z.pdf
This is my connection:
VIO --> 3.3V
GND --> GND
CS --> 3.3V...
I am using nRF51822 and the Software device is S130. The application is based on ble_uart_app. I can declare it as a Bluetooth 4.2 device for lab approval. Right?
I know that Nordic has published a reference antenna design with the nRF52DK. However, I would like to develop a much smaller module with minimal antenna PCB trace or antenna...
I would need more pwm channels, than there is possible with pwm library on nrf51822 (That is 16 channels).
I would like to do it in a fashion, similar to this , using a prescaler...
To whom it may concern,
I use a BLE app via nRF52832_WLCSP, 'ble_app_hids_keyboard' of SDK11(pca10040),SD s132_nrf52_2.0.0, with the HID profile. once I started advertising...
I'm currently using CrossStudio as IDE. I've no problem in compiling and downloading the application in the nRF52832 microcontroller. However the application wouldn't start...
What is the maximum number of connection a central device can connect and control in open mesh? Is 1 to 50 possible? What is the latency?
I am comparing to RFdigital Simblee...
I am trying to encrypt a write on a custom characteristic by setting:
BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM(&attr_md.write_perm);
Then in the write event I read the...
I've tried getting a notification of subscription from a bluetooth event handler like so:
ble_evt_dispatch() is being called from main:
static void ble_evt_dispatch...
Hello,
I am using SDK v12.1.0 and I want to get the debug logs over UART
I followed the Logging Sink Configuration to enable UART logging and compiled the Health Thermometer...
Hi!
I was developing my custom service, and had a question around what kind of functionality is allowed or not allowed within a callback from the soft device or other peripheral...
Hi every one.
I am developing on S130 SDK 11 and I try to use whitelist connection for optimisation.
I have currently a working project which scan for 1 sec for any BLE...
My application is based on the ble_app_uart demo. I want to get the BLE approval from the lab. The lab want me to tell them the Bluetooth profile of my application. How can...
Hello,
I am trying to interface the STPC16CPC26 with the NRF52832. As per the datasheet of the display driver, we have to toggle two IO pins from the NRF which shall be connected...
