Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello Nordic,
I'm struggling to initialize and configure my LIS2DH12 accelerometer for Stream mode after an activity wake.
Platform: Running FreeRTOS with Nordic nRF52840...
Can’t RTT view even provided precompiled code that comes with nRF5 SDK v17.1.0. Tried also the .hex versions that came with older SDK back to 15.3 – same story . Tried even...
Hi - I am trying to use the PCD library in NCS 2.7.0 w/ sysbuild, but this library seems to require partition manager to be enabled (due to the `include <pm_config.h>` in...
Hallo,
is it still true that there is no automated possibility to combine two sdk_config.h files as I read in a several years old post? This is necessary for integrating...
I have a custom board that is in production but is running NCS 2.5.0. I am interested in migrating to 2.7.0 however I am running into a few issues. When I pair to the device...
When I try to build the solution with "Optimize for debugging (-Og)" the linker fails saying `rodata' will not fit in region `FLASH'. FLASH overflowed by 46056 bytes. This...
Hi all.
I have a project on nrf52840 with ble. I needed to add a nrfx timer there. I deleted everything from the main function. Added the code from the timer-counter example...
I'm going to add frequency hopping to ESB
so i have some problem
1、Whether demo is available for learning.
2、for example Gazell frequency hopping ,Where can I see detailed...
Dear Nordic,
I'm unable to register an nRF9161 device on the Verizon Thingspace IoT Network. They have a web UI which allows one to enter an IMEI, ICCID pair. When I enter...
Hi,
We have developed firmware for a custom broad using the nRF52832 with 512kB flash, and our firmware currently uses 48.5% of the flash.
We are using Zephyr and version...
Above is the trace and the commands inserted. We were unable to get a response using the at+cops? command. Both SIM cards were active that we tested. We tested band 12. Could...
I would like to know more about the TLS 2K packet limitation in the nRF Connect SDK.
Is there a way to not be constrained by this limitation. I've seen some posts about...
Hi,
I am using nRF5340 DK and nRF SDK V.2.6.1 for my project
I am following the link;
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson...
Hi,
I'm hoping you can help.
I am using the CENTRAL_UART and PERIPHERAL_UART to evaluate the nRF52840, and using a terminal program works fine.
What I want to do is...
Hi all,
I have a problem that seems very simple, but I cannot make sense of it.
I have a simple setup on the NRF52840 DK that senses a rising edge on pin 1.00 and...
