I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi,
I want to measure a unit current in production.
When connecting the unit to the batteries it do some beeps and after a while goes to sleep.
I want to test the "sleep...
Hi all ,
I 'm currently developping a BLE central with Zephyr and I need to create a default bonded device at startup (I know its address + IRK ) .
Using previous nRF...
Hello, I am trying to create an application on the nRF5340 which samples data at 16kHz and packages + sends it over BLE. This requires a BLE throughput ~1Mbps, which I can...
I am using MX25 external flash with nRF9160. I am unable to find the configuration to use the Zephyr APIs to access the flash. I am able to access it when I am using
spi_write_dt...
Dear Nordic Semiconductor Team,
I am a representative of ELKO EP company and we are currently in the process of obtaining FCC certification for our products that utilize...
I'm using the nrf7002 on a custom PCB, so its a brand new chip. I haven't done any OTP programming for the mac address and instead it's just a hardcoded mac address that's...
Hello Support Team,
I hope this message finds you well.
I've been experimenting with the LittleFS sample available at the following link: LittleFS Sample Code . The sample...
I am trying to use the UART over the onboard USB without flow-control.
I'm currently using a Seeed XIAO_BLE whose bootloader initializes the USB port.
I have a simple...
Trying to build on nrf51822 with segger embedded studio with soft device
I got the error increasing alignment of section .vectors from 1 to 2 because it contains executable...
nRF5340 SDK 2.6.1
I am migrating a project (based on coap_client) from NCS 2.4.1 to NCS 2.6.1, and I get a compiler error:
The offending code is this:
If I open...
I am a beginner in BLE and I want to use one nrf52840 as host and one nrf52832 as controller to learn HCI UART. In nrf52832 I flash the hci_uart program in the zephyr routine...
Hi Nordic Team,
I am using SDK 2.7.0 & board: nrf52840-dk for matter lock application and facing below issue when boot device.
I want to create factory data manually using...
I am trying to build chip-cert tool with nrf connect SDK. Can you please help me fix this issue:
I followed the instruction given on this link: docs.nordicsemi.com/.../nrfconnect_factory_data_configuration...
HI , currently i am using nrf52840 soft device s140 sdk ver. 17.1.0 i have two controllers i need to transfer the dfu ota file form one controller to other controller using...
