Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Hello List,
I have an Arduino Nano 33 ble with nrf52840. It is powered directly with 3.3 Volt using 7 Volt and a 3.3 Volt LDO voltage regulator. It is programmed (via the...
I am using nRF52820 and the SDK is nRF5_SDK_17.1.0_ddde560. When setting advertising data, I am trying to enter the chip's BD address for individual identification. Is there...
So, I follow the zephyr docs ( https://docs.zephyrproject.org/latest/kernel/services/synchronization/events.html )
and define an event as:
However I get the error: ...
Hello, when building the MQTT sample in the nRF Connect SDK, `getaddrinfo()` is returning only -2 when built for the nRF9161 dev kit. I'm using the onomondo SIM that came...
Dear DevZone Nordic Team,
I am currently working on a project involving the nRF9160DK , and I need guidance on how to operate and output GPS values in the debug console...
I am learning how to use MCUMGR. I generally understand it, but I have some concerns.
- The firmware with the private key can also be overwritten. Then it will not boot...
Hello:
We know that 45pin 46pin DEC4 can be connected to inductance to process the ripple of internal DCDC circuit. Then, may I ask which pin is the input power supply corresponding...
Hi,
Can someone please help me to understand how to implement secure boot on nRF52833 chipset?
How to secure root of trust, as once you remove the protection, entire...
With TAU set to 24 hours, when we wake up every 8 hours, everything works fine. When we extend to 12 hours, it takes longer than 10 seconds for a connection to be established...
I successfully enabled littlefs in mcuboot and read/write it successfully (due to project requirements), and then tried to enable littlefs in both mcuboot and app, operating...
Hi,
I am planning to design a new PCB and transition from using the Raytac module to our own custom PCB.
During my search, I found a design that includes an SMA connector...
Hi, What I noticed is that every time I want to flash the nRF9161dk I need to do `west flash --recover` for it to work. I am flashing from Mac M1 (Sonoma 14.5) with `West...
nRF51822QFAC SDK v10 S130
In the completed project it was necessary to make an update. It is necessary to switch off the softdevice and switch to its own Rx protocol. After...
Just purchased a nPM1300 v1.1.0, but it will not connect to my computer. I am using version 2.6.1 of nrf connect, v1.3.0 of the PowerUp app, and what I believe is the correct...
Once the modem is turned off (e.g. using at+cfun=0) - what will be the state of the MAGPIO pins? Will they be pulled to GND or will they float?
Thanks
Ulf
P.S. The same...
