The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I try to enable APPROTECT by nrfjprog but seems not work, I still can read the memory after device (PCA10090) reset.
Here is the commands I test to enable APPROTECT
...
I was trying to update the PPK II software, but I am receiving a error message: "Error: EPERM: operation not permitted, mkdir 'D:\'"
Well, in my Windows environment, the...
Hi,
We have been using the DeviKit for our initial development and now we have developed our own custom board using the nRF5340. I trying to flash the device, but couldn...
Hi, We noticed that if you do not "Disconnect" a SEGGER RTT connection (on the RTT Viewer), the nRF52832 chip latches into using a relatively large amount of power (~3mA)...
I'm running the latest nRF Connect under VS Code on Windows 11.
What used to compile and not show errors (a couple weeks ago, and running 2.6.0) is now showing errors on...
I am having a problem where the UART is getting noise and bad data (I assume framing errors too) with Zephyr drivers. I was wondering how in Zephyr do you check for framing...
Hello,
This demo gives me automatic pairing and password input.
https://devzone.nordicsemi.com/f/nordic-q-a/44658/communication-problems-between-ble_peripheral-and-ble_central...
This question is in lieu of an issue on the repository, because I don't think issues are accepted there?
I noticed I was getting the following CMake Warning:
Could not...
I am running on demo "nrf-knx-iot/samples/light_switch_sensor".
I built the demo and burned it into my nrf52840dk successfully, but I could not see more logs.
I found...
Hello! We recently acquired a Nordic Thingy:91 for prototyping and it was working great until I came into work this morning and it was no longer showing any signs of life...
Hi Support team,
When I compile the application on the network core of nRF5340, the result is like below:
There is a 64KB SRAM1 with usage 0%, could you tell me what is...
Issue: No Interrupt Signal on GPIO0 Pin of MAX30208 Sensor with Xiao BLE nRF52840 Using Zephyr NCS v2.6.1
I was write a code for max302078 sensor driver but in this i want...
In some examples that use nrfx libraries it is necessary to extract a GPIO PSEL, which is usually done like this. Give the following DT definitions
``` leds {
compatible...
Hello. I am developing a product equipped with BLE communication function using nRF52480. I am experiencing an issue where the BLE connection cannot be completed.
[Environment...
Looking at the uart_nrfx_uarte2.c driver it appears that Nordic is not looking for the compatibility string in the driver but instead is looking for uart0,uart1, etc. This...
