Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
Hello everyone,
I am trying to implement the OPTIGA Trust M from Infineon with the nrf9160. Unfortunately I encountered some problems regarding this topic.
I am trying...
Hi,
I'm working with the nrf52840, and I've had success with spi communication in the past. However, I want to switch to spim and am unsure how to do so. Can you provide...
Hey, Having some trouble getting the callbacks to invoke with the generic library on zephyr 1.7.1 to my understanding once it gets the data it should call it. have i misunderstood...
It is a very basic question.
For SOC firmware development with Segger and SDK, which layers of BLE are codes covering? Are Host and controller layers transparent to developers...
Hello,
Due to a routing error, the VBUS pin of the nRF52840 is connected to the GND.
The software works on the devkit but not on my prototype.
From what I saw in...
Hi！
Where master and slave is connecting, and then master is shutdown or move far away.Slave is wait for timeout.But the current of average slave e electric current
...
For my project I need to set the UART0 speed to 9600 baud.
So for testing I tried to compile the "Hello word" example by setting the board configuration file (ncs\v1.6.1...
CONFIGURACION:
NRF52 + SDK15 + SD132 + FREERTOS + NUS.
I have a task sending many packages to a central. I'm having an aboslutly aleatory behaviour: - At some time (could...
I’m checking the transaction of the data between iPhone and a Bluetooth device.
The device is developed by a business partner, but I’m not concerned the FW. I think we have...
Hi,
I am using nRf SDK5 and have a sensor that I am trying to extract the Eddystone UID data from the advertising packet. It shows up in nRfconnect as:
Eddystone UID...
I installed the nrf connect 3.91 with programmer v2.0.1 and J-Link driver v6.88a. However, when I cant seem to see the dev kit on my windows 10. I tried holding the reset...
Hi everyone,
I want to use the RTC module in my code, and I have some questions.
1. What I have understood so far is that the nRF52840 has three RTCs (RTC0, RTC1, RTC2...
Hello,
When using eDRX alone and without DATA (eDRX=81,92 sec, no PSM, no data transmittion,iDRX PDCCH = 1), it's showing an average current of 17,84 uA. This value is similar...
Hi Support team,
I have downloaded nRF5 SDK and found that there is a sample for serial via UART but however the samples ( <SDK Folder>\examples\peripheral\uart) is available...
