Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi, I have a customer wanting to do OTA firmware upgrade using nRFUtil on Fanstel BC840E module.
They have installed the python
D:\nRF_Pjts>python Python 3.9.2 (tags/v3...
Hi!
After cloning a fresh codebase and building the trusted firmware-m sample parts of the mcuboot scripts seem to break:
Traceback (most recent call last): File "/home...
Hi all,
I am developing a low power product based on the nrf52840 module, using the openthread stack from NCS (v1.4.99). Since the device is powered by battery only and...
I would like to use MAGPIO0 , 1 and 2 as 1.8V inputs. I've read through the documentation, but can't find any way to assign pin numbers to these (I'm using Zephyr), only that...
Hi,
First i want to know what is the relationship between connection interval and GAP Event Length.
In one test condition I configured as:
connection interval = 7...
Hi Experts,
We are developing application on nRF52840 based BLE 5.0 module i.e. BMD-340, in short we are integrating the BLE in one of our existing product & upcoming...
Hi Nordic Team,
I'm working with Nordic NRF52832 BLE development Kit. Currently, we are working with DFU Secure bootloader. In this bootloader, we tried the button pressed...
Hello everyone, I am running a code with uart i2c interruption and power management but I have this error : nrf_pwr_mgmt.c:78: undefined reference to `__start_pwr_mgmt_data...
Hi,
Does Nordic have a network-steering function that attempts to join networks on all channels? We will not know which network channel the sensor needs to join ahead of...
Earlier (couple of months) I was working on the examples/peripheral/ppi example in SDK12.2.0. I converted the Keil project inside pca10028/blank/arm5_no_packs to a Segger...
Hello,
I am trying to reset the Zigbee network configuration on my End Device when the user press on a reset button for a long time.
I don't want to restart the product...
Hey.
I have a GPS chip which uses 57600 baud for its rx pin, and 115200 baud for its TX pin.
I need to switch between the two baud rates, and also some times connect to...
I'm using nRF51822_xxAA , with SDK12.3.0 and Softdevice S130 v2.0.1 on Keil V5.29.0.0. And as a central I use Redmi 7A phone with Android V10. I want to sample ADC @ 200Hz...
Hi，all:
There is a question when I run usb_msc example on nrf52840DK(sdk17.0.2)，I do as following steps,
Then,after I press button 1 for serial times,I found there are...
I want to get started with nRF52832 in Arduino. I have a Ebyte development board with E73 module containing the NRF chip.
The hardware is quite similar to Adafruit NRF52...
