I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hello,
I am following the instructions given in this ticket https://devzone.nordicsemi.com/f/nordic-q-a/57896/pdm-interface
When I call the nrfx_pdm_enable_check() the...
Hello，
We are developing wearable devices. 17 sensor terminals send data to the receiver at a frequency of 60hz per second. The data sent by 17 sensors at the same time...
Hello,
I'm interested to know whether the continuous integration and continuous deployment (CICD) is possible on nrf52840 board using Segger Embedded Studio ?
if yes,...
Hi
I currently have a nRF52833 DK which I am using as a transmitter. I also have a custom board with a nRF52811 SoC with an antenna array to act as the receiver for AoA...
Hi,
I am trying to add PWM in my application. My application uses application timer, SPI (my own written code just like CMSIS) and BLE for smartphone communication.
Everything...
I am trying to integrate buttonless DFU with FDS in ble_app_uart example from sdk 15.3.0. Merge hex was done properly which includes bootloader_settings.hex+bootloader.hex...
Hi developers and researchers,
I am working on a project in which multiple nodes are communicating with each other in p2p manner.
My goal is to implement a multiple access...
In the AWS IoT example I have been trying to add RSRP support (i.e. getting RSRP when sending my data packet).
I registered the handler/callback function in main after modem_info_init...
Is the mcuboot module compatible with RTT logging? I've setup mcuboot and my main application but cannot see any logging.
I have the following in both prj.conf & mcuboot...
Dear all,
I just writing a little piece of code (no softdevice, using sdk 17.00), that in theory toggle a led based on 2 compare (CC[0] and CC[1]).
The strange thing...
I am using SD 132 6.1.1 with a GATT server and when the client sends a Read Multiple Characteristic Values command, the nRF responds with Request Not Supported. I need to...
Hello,
I bought the Thingy 91 and tried to follow the instructions on the getting started page.
I started by downloading nRF connect - Programmer v 3.5.0. Then downloaded...
Hi,
I have noticed ever since I updated my nRF9160 DK modem firmware to the latest version v1.2.0 frequent registration dropouts and very sluggish MQTT performance.
My...
Hi, I recently bought a Nordic Thingy 52 and it looks great ! It looks like there is a decent mic and speaker on the device and I was intrigued if the device could act as...
