I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
We've been hunting down an issue there when we call nrf_drv_uart_uninit() we get a high static current which indicates that a clock or peripheral is being left on.
After...
I am getting the error:
There was an error adding your device: No device found with id 'nrf-352656100878829'. Verify you are passing a valid device id and not a device name...
Hello there
I am now using Nordic 52840 dongle hardware ready to be used as a zigbee sniffer, and I have seen that official documentation is feasible.
My current environment...
I am having trouble modifying simple_hal.c from the mesh SDK v4.1 when buttons are on Port1 instead of Port0 on a nRF52840. I have buttons on P1.01 and P1.02.
Everything...
We're attempting to move from v1.1.0 to v1.2.0 of the NCS, in order to take advantage of some driver improvements (particularly DPD in the SPI NOR driver. When we migrate...
Hi,
I am currently working on a custom product that uses module BMD-300 from u-blox, which has nrf52382 chip in it. My application works fine and now I want to integrate...
hi,
Im developing a mesh network based on the nRF52832. I want to send some long message(over 11 byte) without segment, so I enabled the EXPERIMENTAL_INSTABURST_ENABLED...
I turn on the Instaburst feature already , after that , I program serial example to 2 nRF52832 and run it with interactive_pyaci
when i try to do PacketSend with 20 bytes...
I am running a Bme280 sensor with nrf9160 and getting this error msg ( [ 1;31m<err> i2c_nrfx_twim: Error 195952641 occurred for message 0 ) while getting the actual sensor...
Hi All,
Since I measured a very current consumption by testing CLI example (ftd/usb) I'd like to know how to switch my nRF52840 DK as Sleepy End Device.
Any suggestion...
I have a zephyr sample app running on a nrf51822. It's the onoff_level_lighting_vnd_app found in samples/boards/nrf/mesh. I have an iPhone running nrfMesh. I can't find documentation...
Hello, Im working with nrf52832 and sdk15 I'm working with the example: nRF5_SDK_15.0.0_a53641a/examples/ble_central_and_peripheral/experimental/ble_app_hrs_rscs_relay I want...
How can I receive all the packets from all addresses?
In the datasheet I see there's an RXADDRESS which setups the receiver to which address it will listen to. I want to...
I am using the zigbee sdk4.10 cli_agent_router and multi_sensor example. The 52840 module is E73-2G4M08S1C, antenna is a built-in ceramic antenna. During operation, the communication...
