Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
This is the name that is advertised when the device is in DFU bootloader mode.
I've copied the bootloader_secure_ble from /examples/dfu/ but I cannot find where to change...
Hi every body,
My system was able to wake up on gpio on dev kit but after adjusting pin , my custom board is not able to wake up.
I'm in debug mode, it was also working...
Hello,
I am trying to send a single adv packet when a certain condition in the application is met. To do this I am calling ADV_start for the initial adv packet and then...
These questions are in the context of using an nRF52840 in a serialization application. But I don't believe this will impact the information I am trying to understand. The...
I want to program the firmware into a nrf52840 on our custom board to be the NCP and do the DFU over thread. I can not use the DK board and have the nrfutil load the firmware...
Hi,
Our application uses MQTT over TLS to talk to a MQTT broker.
The MQTT APIs used are like in the 'mqtt_simple' sample code.
When mqtt_connect is called with invalid...
Hi,
I'm designing an application using SEGGER Studio for the nRF52832. I have based my application on the template peripheral example.
What I want to do is to trigger...
Hi--
I tried to implement an internally managed RTC using the app timer library, but came to find the error on that is too much for an RTC (~25 min lost over a few days...
I want to know which pins serve the purpose of TX and RX in nRF51822. I suspect its the ANT1 and ANT2 but i want to confirm and also if the following would be a good way to...
I just buy nrf52840 Dongle.
I connect nrf52840 Dongle to my USB port and open nrf Connect.
I look at guide https://devzone.nordicsemi.com/nordic/short-range-guides/b/getting...
Im using sdk 15.2 with 2 nrf52840 boards, i would like the server to connect to a particular client. How to add the devices to whitelist in sdk 15.2 ?. I have gone through...
Hello,
I am working on a scanner code, I have initialize my scanner with this parameters.
and in nrf_ble_scan_init()
It is getting reset once in the beginning like...
Hi,
without any obvious reason one of our nRF52840 DKs stopped being visible over the USB (J2) interface. The nRF52840 is still functional and can be programmed from another...
Hi. I'm using nRF52832, SDK13.0.0, S132.
First of all, I already know this Q has lots of Q and A.
But I'm so confused which case do I pick.
In my case, iPhone has...
