Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello. I am trying to implement stable connection between my nordic nrf5340 and Samsung Galaxy Buds3 earbuds. I did it based on ble audio example with two connections (one...
I have a 7002dk dev kit. Currently for evaluating the nrf5340, which will be used in my product. Currently i am trying to evaluate if it is possible to use the nRF5340 USB...
Hi,
I am using two nRF52833 DK and both are connected with nRF21540.I notice that when I have a very high throughput, never stop sending 244 bytes, I will notice that average...
Hello, I connected my (working) PPK2 and opened the PowerProfiler. Immediately, a "DFU needed" message popped up.
I DFUed the PPK2, and in the logs, it wrote DFU successfully...
Hi,
I would like to ask about the future plans for Zigbee development, as the current situation is a bit confusing.
From what I’ve observed, Zigbee R22 has been deprecated...
My team recently acquired two NRF24 transceivers to use on our drone project. Personally I've used NRF24 modules before and have successfully paired them with Arduino and...
Hi all,
i just received 2 nRF54L15-DK boards. Both I am not able do program - I tried:
1. nRF Connect for Desktop
* I did not make any change on the board afre unpacking...
I want to use the boards NRF-5340DK or NRF-52840 with the external host for the channel sounding feature. Can we use the feature on the mentioned board? If so, can you please...
I'm trying to send and receive an extended advertisement packet with about 100bytes of payload.
I started with the sample extended_adv example.
I 1st validated that using...
Hello. We are updating firmware to use nrf sdk 2.9.1 (from 2.5.2). Below is my proj.conf, should I expect any breaking changes?
############################
# Stacks...
Hi,
I want to configure the nRF9160's internal flash storage_partition, it has 32KB currently, I want to change it to 100KB. How to do that? Using nrf9160dk_nrf9160_ns.overlay...
As the title suggests, I want to use west build without having to include the BOARD_ROOT parameter.
I have already referred to this link , but the results were not as expected...
Toolchain v2.70, SDK v2.6.1, VS Code, Windows
Code derived from UDP sample works on DK board but fails on custom device.
Device is using DK board configuration, but no...
I have used ADC Channel 6 (P0.30) for voltage measurement using NRF52832. Previously It was working well. Now it is returning an error.
00> [00:00:00.398,345] <err> adc_nrfx_saadc...
Hi
I have been working on a project for some time, using the SDK and the nRF Connect for VS Code plugin. A few weeks ago I stepped away from this to take on different work...
