Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
This is not really a problem - more like an enquiry
Is it possible to gate PWM output using another GPIO pin e.g. if the second pin is low then so its the PWM otherwise...
Hello,
I would like to test and adapt the example "ble_app_uart_coexist" with my nRF52840 DK. Unfortunately, I believe that this one is only intended for nRF52832 and softdevice...
Hello,
I am trying to use the BMD-350 evaluation board to program a standalone BMD-350 module on a custom PCB. I have followed the instructions in the documentation to connect...
Hi,
I'm using custom board with the nrf42840 and I need to use p1.09 as a GPIO.
How can I do this in a debugging mode (using the PCA10056 as a jlink)? Can I get a code...
Hi,
I want to get interrupt on GPIO using gpiote module.
I searched for example but couldn't get it.
Can you guide me how to use gpiote in nRF9160 ?
Regards,
Smitesh...
Using Fanstel BT832A BT 5.0 Module which utilizes SoC nRF52810 QFAA
1) Yes or No: can I configure a GPIO as a Timer/Counter Input so I can feed a high frequency input into...
Hi,
I just wanted to know which flash is used by the flash manager within the SDK Mesh v2.2.0 onoff client/server examples ? Is it the 1MB internal flash or the external...
Hello,
During development of a custom board, based on the BMD-300 module from Rigado, which uses an nRF52832, we ran into a SoftDevice fault under specific circumstances...
Hi,
After trying to work out why one of our nrf9160 DK:s cannot execute any AT commands using the at_client sample I tried redoing the getting started guide to make sure...
Hi, I am making my own bluetooth custom board with nRF52832. Till now, I made my custom pcb following the infocenter layout and chip antenna like below.
Now I want to...
Hello All,
I have 2 evaluation boards nrf53840 EVB "PCA10056".
I would like to run on them the "ble_app_uart" in " nRF5_SDK_15.3.0_59ac345 " as following:
A custom...
I am working on BLE mesh network,initially I have tested the light switch demo example it is working fine.Now I want to test relay functionality by using light switch example...
Hello everybody,
I have two nRF51822. One of them is connected to MCU (STM32 Development Board Nucleo 32) via USART with 115200 baudrate. The other one is connected to USB...
I'm having issues trying to program a custom board with NRF52832_QFAB in DC/DC config. I couldn't reach a complete programming getting error in open ocd with two programmers...
