Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Como faço para habilitar o registro de logs do mcuboot para visualizar os logs de atualização DFU no nRF Connect SDK 2.9.2, usando o nRF54L15 em uma placa personalizada com...
Hello team,
I attempted to measure the sleep current on the nRF54L15 DK board, but I’m seeing a very high current draw of about 74 mA.
I built and compiled the peripheral_power_profiling...
Hello,
We are developing a custom board that uses the nRF54L15 chip, and are trying to flash an application along with MCUBoot to allow for OTA updates. When I flash the...
Hi Nordic folks,
I'm trying to get the nrf54L15 in a Fanstel BM15M to go into the system OFF state and be woken up later by a timer. All the documentation I've seen says...
What's minimum hold time for a pin reset on nRF54L10? https://docs-be.nordicsemi.com/bundle/ps_nrf54L15/page/pdf/nRF54L15_nRF54L10_nRF54L05_Datasheet_v1.0.pdf doesn't state...
Hello, I am developing an application that uses Bluetooth Channel Sounding, and for that reason I need to have two devkits connected to my computer at the same time, but the...
Hi there,
I was designing an add-on development board to go onto the development kit to test a 1.8V application. I need VDD:nRF on the 54LM20 to be set as the same as VDD...
I connected the new nPM2100 EK to Linux PC and opened the nPM Power UP application. In the app I'm able to select the EK. The nPM Power UP tells me that " Programming required...
I have an NPM1300 demo board. After testing, the default voltage of VOUT1 is 1.74 V. If I use this voltage to power the VDD of nRF54L15, will it affect the power-on reset...
Hi Nordic
We plan to use 54l15+7002e, how much storage will spend for nRF7002 up layer stack and application(e.g typical Wi-Fi STA with TCP client connections)?
What I've tried:
Testing Summary: SD Card on Port 2
Setup : Wired an SDHC card (Transcend 8GB) to the Connector P2 (middle header) on an nRF54L15 DK v1.0.0...
In my code, I find I can start up the ble pakage sending. but it alway send out without stop. I need send out one package. and stop. In my radio callback. I do call this task...
Hi Nordic Support Team,
I am working on a Matter application using the nRF54L15 , and I have a few questions regarding the external flash configuration.
I noticed that...
nRF Connect SDK v3.2.1, nRF9160dk
Hi,
I'm working on an application which connects to a MQTT broker over cellular network, and have MCUMGR enabled for firmware updates...
