I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
Hi,
I am new to MCUs and I am trying to send information from NRF51 via UART (not BLE UART) to Putty. No matter what I try I can't seem to print anything on Putty. I started...
Hello!
I was copy template project from preinstalled folder to the desire one. When I opened program in new folder, the translate operation work fine. But when I pressed...
I would like to configure the connection timeout with the S130v1. This timeout is described in the following sequence diagram: infocenter.nordicsemi.com/.../group___b_l_e___g_a_p___c_e_n_t_r_a_l___c_o_n_n___m_s_c...
Hi there,
In the process of moving from SDK 10 to SDK 11, I've also been migrating an accelerometer driver over from using straight nrf_drv_twi code to the higher level...
Hello,
Is it possible to use easyDMA to transfer from GPIO to memory without involving the CPU? We need to read from a parallel bus for a short duration, without losing...
When setting up a 1Mhz square wave using NRF_PWM on the NRF52 or GPIOTE on the NRF51 while BLE is advertising, the PWM stops when the radio is active. The problem doesn't...
Hi,
I'm developing a BLE application for the nRF52 and I wish to use directed advertising and the whitelist.
I initialise the Bluetooth advertising using the following...
I have been using softdevice S130 version 2.0.0-7.alpha with SDK 11 in Keil using the pack installer. How do I change my project to work with the updated version that doesn...
Hi,
I believe there's a minor bug in low_power_pwm.c regarding pwm_state.
The routine low_power_pwm_start sets the pwm_state to NRF_DRV_STATE_POWERED_ON ; but it then...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
I am troubling shooting some issues between my device and iPhone using nRF Sniffer.
One of the errors the sniffer captures is this:
Master to Slave: Rcvd Read By Type...
I will be using the nRF52 adc from -20C to 85C and am trying to determine if I need to calibrate and if so how much temperature difference I can have before it is time to...
Hi, I'm working on the nRF52 with S132 v2.0.0.
I am using a self-implemented "connection manager" that tries to establish bluetooth connections to pre-configured auxiliary...
Hi,
I am using 2 x AA batteries which gives 3V. Planning to enable all the internal LDOs (1.2V, 1.8V and Radio LDO).
VDD and AVDD are shorted on Board.
Will the device...