Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hello NRF team,
We have been using NRF52832-QFAA based dev kit from Sparkfun, which has 512KB Flash / 64KB SRAM. I developed the app on Arduino whereas I flashed the bootloader...
Hello!
Here is a story I am sure you have heard before. I am evaluating the NRF9160DK and seeing what is the lowest power consumtpion we can get when sending data to a server...
I have an existing product using the nRF52832 SoC rev 1. We must transition to rev2 since rev1 is no longer sold. We use SDK12.0.0, with S132 V3.0.0. Have these software components...
Hello Team,
I have downloaded the Zephyr project and working on the LwM2M sample client application to make nRF52840 DK as an LwM2M client. I have followed the below link...
Hi,
Referring to White Paper nRF9160 Hardware Design Guidelines v1.0, what is the scenario (supply voltage, band, antenna VSWR, TX duty cycle...) behind maximum heat power...
Dear Sir,
I'm using nordic's example codes above to tx and rx, but i can not get them working properly. the LEDs should light on the receiver side according to the example...
I have a strange issue on the nRF9160-DK board using the nRF Connect SDK, GNU ARM for GCC v10.2.1, built using makefiles.
I have two threads that both wait on a semaphore...
Hi,
I am trying to change the tx power of Zigbee using the following APIs :
1) zb_set_tx_power(0x32); 2) nrf_radio_txpower_set(NRF_RADIO_TXPOWER_NEG12DBM); 3) nrf_802154_tx_power_set...
I am currently using a nRF52-DK to follow the connection between two external devices. I run the sniffer and start/stop the sniffing via Wireshark. When I start sniffing,...
Dear Team, I face Following error with example downloaded from Github,
error 1) Output/Release/Obj/saadc_pca10040/ses_startup_nrf_common.o: in function `InitializeUserMemorySections...
Chip: NRF52840
Firmware platform: Wirepas V5
Hello!
I am now writing firmware for a product based on HW&SW mentioned above.
It is powered by battery and sends data...
Dear Sir,
please do me a favor to reply on my following question.
our project is a keyboard which we expect can work on both ble and 2.4G. we will use other brand of of...
Hello
I am using nrf52832 and sdk v17.0 I recently succeeded in controlling several ws2812 LEDs through I2S. And now I'm going to combine these codes with the others.
...
