I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Dear all,
I have picked the Ruuvi project : https://github.com/ruuvi/ruuvi.firmware.c and change the configuration to adapt with nordic dongle.
But after flashing, my...
Hi,
I am evaluating LC example, I am using an occupancy sensor. So whenever there's an occupancy it's detecting and turning the lights ON. But even when there's occupancy...
Hi,
I have created an eclipse based makefile project for nrf51802 module.
The sdk version that i am using is 12.3.0, and softdevice S130 .
Taking reference of ble_app_uart...
HW setup is my boart connected to a windows10 PC with an uart link.
I tried secure_bootloader_pca10100_uart_ses_nRF5SDKThreadv4.1.0.zip example, with some modification for...
Hi All,
I followed this article and got eclipse to work. I can use debugger, single-step, place a breakpoint. All good.
I noticed that disassembly window shows opcodes...
Hello,
I am working on a project that uses Azure as a cloud IoT provider and the NRF9160 as a gateway-like device which is supposed to make simultaneous connections to up...
Hi,
Just wondering if it is possible to configure the UICR Customer registers after erasing and flashing/programming the nrf52832. The hex file used to program the device...
Hi Team,
I wonder the operating system which has been ported on nRF52840 DK, I found multiple IoT OS what nRF52840 supports like ARM mbed, Zephyr, Contiki, etc. But can...
Using NCS 1.3.1.
Why is nrfx_spim_xfer() asserting when using NRFX_SPIM_FLAG_HOLD_XFER flag and a ss_pin ?
When not using a ss_pin in the spi config but configuring with...
HI,
I was trying to update firmware on thingy 91 using MCU bootloader. Now when I trying to upload again it is keep showing one error.
Error while probing devices: Error...
Hello,
I'm using nRF52832 and SKY66112-11 PA/LNA connected to increase the range. I'm using nRF5 SDK 17.0.2 and nRF5 SDK for mesh 4.2.0
I followed this guide to use PA...
Hello everyone,
I'm programming for nRF52833, using SDK17. When I program for scanning filter (SCAN_NAME_FILTER and SCAN_UUID_FILTER) and debug, I got these errors. I don...
I have a ST link V2 with swd interface support. For one of our existing projects ( custom board ), we want to examine the current consumption of BMD-350 ( NRF52832 ). Hence...
I am currently tasked with programming the NRF52810 to boot up upon a button press and then sit and wait for further button presses to trigger various functionality including...
Good afternoon
According to the project requirements, two keys were added to the compiler settings for stricter project verification:
-Wsign-conversion - Checking for...
