According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
I'm developing on the nrf52840PDK and I was running the cdc_acm exmaple in the SDK to observe the token exchanges between the host and the device.
In the Nordic52840 Product...
Hi all,
I have a module with nRF52832QFAAB0 IC, I'm looking for the IC revision in the compatibility matrix here.
Unfortunately I didn't find any packet variant and build...
I've run the Demo(thingy52-mesh-provisioning-demo). And it works. Now, I want to expand the function.
I 'd like to create more model(for example, sensor model for humanity...
Hi,
Sorry for post here again but i'm having a lot of trumble. I'm actually at the step 4 of the guide, which is the page generation.
I've made correctly all the previus...
I am working on a nrf51822 board and trying to run ble_app_hrs project using nrf sdk 12.1 and s130 softdevice. I converted the uVision project to the Segger Project using...
I use SDK 12.3.0 with IAR
If there is an option to know the last page that programmed?
For example:
Linker: ROM start address 0x1F000 end address 0x76fff
But...
Yesterday, I upload the thingy sdk v2.1.0 in keil uVision5 and rebuild it. After rebuild, it showed one error namely "fatal error" due to the large size(122kb). please suggest...
I am using sdk 14.2.0.I am trying to connect mpu9250 with nrf52832 dev board. whenever I took data serially on putty it is true...but whenever I try to connect it with NRF...
Hi,
I'm new to Segger Embedded Studio developmemt. And now I met a problem similar to Placing data at a specific memory address with Segger Embedded Studio .
I need to...
Hello,
We're creating a program that advertises and reads scan requests RSSI values to determine distance of central device and display them using the onboard leds(1-4)...
We are currently evaluating use of NFC on a nRF52840 which should get powered via VDDH.
Section 7.3 of the data sheet states that NFC can be used in any power configurations...
Hi Nordic engineers,
I found a strange problem that NRF52840 voltage of io high level is just about 2.65v~2.71v. I am sure that the voltage mode is normal voltage mode...
Hello,
I'm attempting to solve some issues with my BMD-200 (nrf51822) not getting the SD BLE_GAP_EVT_DISCONNECTED message. I currently Don't seem to be getting this message...
Hi, I'm not able to find the memory layout of the nRF52840 without the SoftDevice. I'm working with the nRF52840-Preview-DK and the SDK v15.0.0. I don't need the SoftDevice...
Hi sir,
we use nRF 52832 with ESB protocol. and we use ACK to send payload to PTX , but we found must use the same pipe which PTX used pipe to send ACK .
so , I have two...