Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
I am trying to integrate DFU into ble_app_uart example.
I am using nrf51422 board, sdk v10.0.0, soft device "s110_nrf51_8.0.0_softdevice.hex".
I have made some changes...
I'm trying to use Pin 0.21 as SCLK in the SDK15.2/examples/peripheral/spi/pca10056/blank/ses.
The example works fine with CLK on pin 3 (default) and on pin 29 (just tried...
Hi,
I created nrf52 project on Segger studio. I'm writing directly registers.(not SDK)
It includes i2c,uart and adc, this part is working now.
I want to add SoftDevice...
Hi,
I'm using Keil development tool.
The original bootloader start address is 0xE6000 and new bootloader start address is 0xE5000.
When I update to new bootloader, it...
hi...
What are the things I can check if I can't find my nRF51 upon scanning for BT devices? I am using nrf52832 and can successfully program the device via a Segger J-Link...
Simple and perhaps stupid, but important for me: the reports of detected devices I see in nRFConnect (desktop or mobile version) are based ONLY on BLE advertising packets...
Hi,
I am experiencing problems with the app_error_handler function defined in app_error_handler_iar_c provided with the SDK V15.0.0.
If the function gets called when debugging...
HI team,
I am a beginner of Nordic nrf52840 DK, I would like to control the AC ceiling fan using the nrf52840 board with pwm library. As, I can see we can use either single...
errr_code=sd_ble_uuid_encode(p_target_uuid,&raw_uuid_len,raw_uuid);when i debug and going to find uuid my debugger will move to NVIC_systemReset.i am running uart central...
Dear all,
I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the static key feature. But every time when I configure the static key including letters...
Hi,
I am currently trying send value to a write characteristic of the server of a custom central device with a nrf52832 peripheral device. I have been able to connect with...
Hi
I am going to use the ble_app_uart example , the sdk version is 15.2.0
I only modify the vendor specific UUID , and download in the NRF52840, it does not work, i can...
Hi there,
I am about to perform an RF emission test to my product which is using a nRF52 chip and different RF sources as wifi and cellular and I was requested to:
...
Hi,
Using the gls example, as soon as I try to connect to it using NRF Connect on my iPhone, I get the "Failed to secure connection. Disconnecting." error. Once the error...
Dear all,
I'm designing a layout with nRF52832 and in my layout I didn't use pin 37 and pin 38 (P0.25 and P0.26). I noted that in PCA10040 v1.2.1 development kit there are...
