I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I am having trouble with the service discovery of my application. When I click Discover Services it takes several seconds to discover all of the services. For example between...
Hello!
I have a problem with ble DFU application upgrade. I use the Master Control Panel 3.10.0.14 under Win 7 on virtual machine and nordic ble usb dongle.
On the firmware...
I used AdaFruit Bluetooth LE shield previously that uses nRF8001. I can define new customer service using nRFgo studio (which only supports nRF8001). I am moving towards using...
Hi,
I am using pca10040 board. i need to toggle a led in 5sec once. I tried to change the prescale value. But im not able to get that much time delay.
Can any one help...
SDK Version: nrf51_iot_sdk_0.8.0_f1f6187
In SDK all examples are given for PCA10028. Is it possible to run on PCA10001?
What I have done so far with PCA10001:
1.Programmed...
Hello,
I have modified the Android-nRF-Blinky Application to use it with the Datathroughput Demo on the nRF52 DK.
The android application runs on a Nexus 9 with android...
Hi, i try to understand how to use mode for supply voltage measurement. But i have a problem and i get always 1.225 volt
hal_adc_set_input_channel(HAL_INP_VDD2_3);
hal_adc_set_reference...
Hey all,
Wondering if we could use an external 65.536KHz LF clock, or thereabouts, instead of the 32.768KHz? We need better resolution for the RTC, but don't want to turn...
hello im from mexico, last week i order 10 NRF24LE1 and arrived the next wake,
but before i have many cuestion about.
someone can tell me that the burner can work?
compiler...
I had a mbed firmware running on a ST Nucleo 64 that periodically query a sensor for data. It only use the I2C, a button interrupt and a LED for heartbeat. I ported it to...
Hi,
I want to know that if the TWI easyDMA in nRF52 can help in achieving this task:
we want to read from TWI each 10msec based on a timer interrupt and write...
Hello:
I have detected a problem with a timer on my program.
I can solve it, but I would like to understand what is happening exactly.
My program starts to scan BLE signal...
I'm writing the client-side code for the Nordic DFU service and according to the spec, the DFU packet characteristic uses Write Without Request. Are there any examples of...
