Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,
We are currently working on a project where we need to sample a frequency input on a GPIO pin up to 6MHz. I have tried GPIOTE and TIMER with a PPI channel, but can...
Hi
I am reading the exernal power in one ADC channel and the backup battery in other ADC channel. When my hardware has not external power and the backup battery drop until...
Your old documentation website ttps://infocenter.nordicsemi.com/ carries a banner saying it will be shut down on 18 June 2024. Please don't do this! I can't find equivalent...
I'm running NCSv2.6.0 on some custom hardware, with an nRF52832 IC fitted. I'm trying to trigger an ADC measurement every ~ 300usec using a Counter, so need to set the Counter...
Hello community,
I am working on a custom nrf5340 board design, that uses the BL5340PA external antenna module to implement the nrf5340 chip in the design. The BL5340 module...
I have recently upgraded my SDK from NCS V2.2.0 to V2.6.0, and have come back to some firmware I had working under 2.2.0 as I need to progress that. The firmware is based...
You may ask what poolside means. It means at my community pool, where I don't have Internet access via Wi-Fi for my laptop.
I wish to run some AT commands like AT%NCELLMEAS...
Hi, I have followed the instructions in Securely generating credentials for nRF91 Series devices - nRF Cloud but cannot connect to nRF Cloud.
I think the instructions on...
I'm confused about the use of these two functions. I want my app to sleep immediately upon start and then wake up and do a BLE advertise when I press a button.
I...
Hello everyone,
I've been spending a lot of time to fix the issue not being able to enter DFU mode with the following error. I've changed so many versions of GCC, but it...
Dear Nordic devzone community,
I have designed a custom board using nRF9160 and I am able to send and read out certain AT commands which confirms to me that most of the...
I'm transitioning from SES to Visual Studio Code.
In SES, I can define multiple builds and then define preprocessor options (eg. -DOPTION1) for each build definition
I...
Hi there,
We are quite new to Zephyr. We are currently porting our existing app onto Zephyr as a test. We are currently using NCS 2.5.1
So for our existing application...
I needed to add my own partition to the primary flash, and was able to do so successfully by adding a section to the device tree partitions.
However, when adding MCUBoot...
