Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
I am designing a wearable device that uses BLE and UART. During the development stage, I worked with the nRF52 Development Kit and started with the ble_app_uart example from...
Hi,
What would be the best way to alter pin's functionality from UART TX ->RX->GPOUT ->GPIN in runtime? (NCS2.5/Zephyr nRF52840)
Is it supported by Zephyr/devicetree...
Hi. I can't build the hello_dect example using cmake, the build process is failed with the following error: In file included from /home/cybermag/ncs/nrf/modules/trusted-firmware...
Hi,
In this post Hung Bui states that there can only be "maximum 4 pin events, each for one GPIO pin (so max 4 pins at a time)". This is (apperently) not true since I...
While scanning for devices with NCS 2.9.2 my device suddenly stops sending adv reports after a few hours.
It seems like this might have been fixed in a recent version...
BOARD: nrf54l15 DK
SDK: 3.1.0
Hi,
I am trying to setup my low power preipheral with a new ble address via bt_id_create.
Everthing works fine when I use the exact...
Hello! I am developing an application for the nRF5340, and I am using split cores, so the controller is on the network core and the application is on the other core. I want...
Hello Nordic Support Team,
I’m working with an nRF5340 on nRF Connect SDK 3.0.2 , using both the Distance Measurement (DM) service and BLE DFU.
My application topology...
I am trying to implement serial recovery via USB on NRF 5340. I have come across this page that I used as a guide:
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf...
Hello,
I am in the process of upgrading our product from SDK 1.6.1 to the latest SDK (3.1 at time of writing). I am quite lost on the external flash through using devicetree...
I've pulled FDS and LESC into my development project. I've noticed now, when I do --reset --sectorerase --program "#H" --family NRF52 --verify, occasionally I see program...
Hi,
I'm trying to perform some measurements on two nRF54L15DK boards and would need to reset both their SYSCOUNTERs at the exact same time. I thought DPPI would be perfect...
Hi,
I have a question concerning the box ID IMEIs. If we have two boxes with nrf9161 modems, do we need to make sure that the modems from box A are assigned only IMEIs that...
