Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,
I've successfully setup a development environment for nRF Connect and Zephyr on windows (VS Code extension) where I can build, debug and flash code to my board...
The nRF52833 isn't supported Bluetooth low energy by nRF Connect for Desktop as list device in link https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrfconnect_ble...
Hi, I'm working on nRF52840-DK board and NCS SDK-v1.7.0 on Windows with Visual Studio Code.
We want to add support for Image validation for imaged signed with ECC curve...
Hello,
I have nRF Connect Desktop v3.9.1 for MacOS installed. I am trying to run the "Bluetooth Low Energy" utility using a nRF52840 dongle.
If the only device connected...
Hello
I was trying to get this example ble_app_template to work but it seems like it doesn't, the code is executed on the ic since I was uploading some code to blink a light...
Hi,
I have a question about running a secure service that does RSA encryption and decryption in SPM using mbedTLS.
I am using SEGGER Embedded Studio for ARM (Nordic Edition...
Hello all, Currently I am developing a code in which a central (nRF52840) scans and reads adverisement packets from 2 beacons (no connection required). I decided to use an...
Using nRF52832, I've got some firmware that uses NFC pins (9 & 10) without problem, using CONFIG_NFCT_PINS_AS_GPIOS.
I'm now trying to replicate this using nRF52833, and...
I am working with the nRF52840 under Zephyr to develop some wireless sensors. The issue I am having I build a test module using the nrf/samples/light. This running on the...
Hello,
I've been experimenting with nRF Connect SDK and compiling a program which supports provisioner mode, provisioning and direction finding.
Everything compiles and...
Hi everyone,
I work with an nrf52840 and SDK15.3.0 and SD 140-6.1.1
I have a board with two micro controler, one nrf52840 and one STM32.
I want to know if it is possible...
Hi
I need to do DFU OTA for my Custom board. So, I need to Know the procedures which I need to follow for nrf5340 and how can I do that on NRF Connect SDK. Kindly help me...
i have no idea on how to read the device id of the qspi please guide me to do so i have gone through the qspi example there could not any instructions to read the device id...
Good day!
There is now way to restart dfu_mcuboot with
CONFIG_DFU_TARGET_STREAM_SAVE_PROGRESS
Checkout:
dfu_target.c
next dfu_target_mcu_boot.c
and finally...
I've been developing in the following environment:
Windows 10
NRF Connect for Desktop
with few problems for the past six months.
On Friday 12/10 I was suddenly unable...
