Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Hi, I want to use TrustedFirmware-M as a secure backend for an application that uses Mbed TLS in the non-secure domain, and this seems to be artificially limited - the MBEDTLS_USE_PSA_CRYPTO...
Hi All,
I am developing one device using nRF52840 based on Zigbee protocol.
Currently I am using nRF52840 Dev-kit and nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8.
...
Hello,
as discussed in the email with Joakim T., could you please provide us a sample of how to use AT command %KEYGEN to generate CSR using the ECC private key? If you...
I am using NRF52840 with SDK15
I am using AES 128 Encryption and am confused on the documentation:
During the encryption operation with nrf_crypto_aes_crypt or nrf_crypto_aes_finalize...
Hello everybody,
I'm currently trying to create a Bluetooth Low Energy Mesh network of multiple nodes that I can control using a Bridge application.
I use a nRF52840...
Hi,
we are developing one prototype where we are using two MCU for different task. we are planning to give common reset button (for customer access) for both the MCU using...
Hello,
I am attempting to create an example project of the Asset Tracker using the NRF9160DK.
I have installed SES using the Toolchain Manager.
I have attempted using...
Hi,
i'm using the nRF5340 DK and SEGGER Embedded Studio V5.50c. Today after starting SEGGER i was asked to perform a firmware restoration for the j-link if the nRF5340 which...
Hi,
I need to use two uarts for the project requirement. UART0 is enabled and working successfully. And I am trying to initialize UARTE, but I am not getting any output...
Hi,
I decided to try the “ble_peripheral/ble_app_gls” example on nRF52-DK.
While I could connect to the kit, pair and bond successfully, when I deleted the device from...
Hi:
I test this hids project, if remove the function bt_conn_auth_cb_register(&auth_cb_display). The iphone will require paired while reconnecting after disconnected. Can...
I am trying to determine the service handle of the nus example, to be able to verify that the central has turned on notifications.
I am using the sd_ble_gatts_value_get...
Hi,
I have a question about 'Thread Secrue DFU',according to the ' https://infocenter.nordicsemi.com/index.jsp ' ,the 'Thread Secrue DFU' does not use softdevice of transform...
Greetings,
CPU = nRF5340
SDK = nRF Connect SDK v1.6.1 and 1.6.0
Board = custom
For the nRF5430, we have a custom board that uses active high logic to turn LEDs on...
