Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi, I'm a beginner with these Nordic DKs. I'm just trying to connect it to my computer and get familiar with the hardware and firmware. However, when I plug in the DK via...
i want to store and retrieve data in flash. i followed steps as in the sdk infocenter but i am not getting the interrupt after fs_store(). Actually return value of fs_store...
Hi,
In my current project based on SDK 15.3 and sd140, I am using nrf52840 in both peripheral and central devices. I need to be able to maintain 10 concurrent connections...
Hi i am using the nRF52dk and i am trying to control a bldc can anyone help me to guide in how i can generate a pwm to get a sin wave
best regards Nikolai
Currently I want to build the light_switch examples from the nrf5_SDK_for_Mesh_v4.2.0 on my nrf52840 dev board but this gives the following error "boards.h: No such file or...
Hi,
I am working on a project of throughput data from sensors to my central via nrf52805 through a notifying service (SDK16.0.0).
Symptom description
We have app from...
Hello,
I want to use I2C slave on nrf9160, but there is no I2C slave driver implementation.
So I read that instead of this, I can use nrfx twis drivers on nrf9160.
I...
What am I missing when
NRF_SPI_MNGR_DEF(my_spi_mgr, 2560, 0);
causes:
../../../../../../integration/nrfx/legacy/nrf_drv_spi.h:120:37: error: 'NRF_DRV_SPI_INSTANCE_0...
Hey all! I have been using your amazing app timer for a while now but I was wondering if there was a better way to create a low power delay than my current design which goes...
Hello,
My application is the ble_app_uart example of SDK 15.3 extended, and using S112. I'd like to use constant latency mode. Given the app uses S112 for BLE, should I...
Hello,
In demo code of Central_Uart code in nRF Connect SDK, when the scanning is started the scan address (MAC) keeps on changing everytime the code is run. (The central...
Hi, We have a product with nrf24L01p Gazell (LastChangedRevision: 133) that acts as a Host. At the moment I'm trying to pair with this host via a PCA10040 Devkit ( nRF52832...
After nrf52382 is written into the firmware program, the test runs OK. After it is placed for a period of time, it is checked again. It is found that it is not running. Use...
