I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
I tried to install the nRF Connect SDK v1.3.0-rc1 error
I open git-bash.exe to execute the ncsmgr init-ncs command, the following error occurred during the installation...
nRF Connect SDK v1.3.0 using nRF Connect v3.4.2 - ToolChain Manager
I am trying to install nRF Connect SDK v1.3.0 using nRF Connect v3.4.2 - ToolChain Manager using nRF...
I am writing a code to blink the LEDS , the 3rd one is not turning off.
Here is the code-
#include <stdbool.h> #include <stdint.h> #include "nrf_delay.h" #include "boards...
Hi,
My device is using nRF52840 with s140 of SDK v16. BLE feature is used with SD .
Sometimes application hard faults in SD are observed in devices deployed. It is quite...
Hello,
I find that after I DFU a new application (using the nRF Connect Mobile App), my device boots into that new application and reconnects to the App, as expected. Then...
Hi,
I am using nRF51822-CEAA with S110 SoftDevice on a custom board which is commercially deployed now. I am using IAR 7.80.2 and Segger JLink Ultra+. I found there are...
Hi community ! I saw a lot of topic about that but i'm working with SDK_Mesh_v4 and i don't get what i want. Does someone have a working example of sending string over Mesh...
Hello!
I have a rather vague question and want to apologize for that beforehand.
I was wondering if it is possible to connect a JPEG camera to the nRF9160 DK (i.e https...
Hi, We are in the production phase of our development, and inadvertently , the mcuboot bootloader set the DCDC on a few units. As described here, https://devzone.nordicsemi...
Problem with setting two uart on pca10040 board
hello
I am reading the log by teraterm by connecting pca10040 board to PC via USB.
I am trying to connect 6pin and...
We are using manufacturer specific data to broadcast data at 10Hz.
We're about to do some testing to evaluate different adverting and scanning parameters to find the best...
Many of the sdk_config.h examples have both NRFX_FOO_ENABLED and FOO_ENABLED defined.
So, imagine my surprise when I change, say, NRFX_TIMER3_ENABLED to 1, still get link...
Hi, is it possible to measure NRF52832 vdd voltage using LPcomp. I know I can do it with ADC but it draws a lot of current. I'm thinking if I can compare VDD to lpcomp reference...
Overview: number of bytes sent by ble_app_blinky at notification is determined by (note my changes for debug:
in ble_lbs_init() of ble_lbs.c and not by:
in ble_lbs_on_button_change...
I aam badly stuck in this error and dont know what to do with this i have downloaded ble adc scan mode example and running it on sdk17 using SES .i have removed powerclock...
