The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
hello Nordic
recently i encounter a claim that nordic to nordic BLE is faster, or capable of transferring more bits of data per second, then a nordic communicating with...
Hi,
I Have been trying to understand how to flash the nrf9160 IC using SWD and segger. Completed up to the build and run.
Need to know If I make some changes in code...
I am on SDK15.3, NRF52840, armgcc, makefile, console
I need to print a double float number in format of "x.xxxxE-xx". I already know that NRF_LOG can only print float with...
I am using sdk17. I'm implementing central, and I'm using app_ble_out_c to implement it. But there's a problem. This example matches only the specified nus uuid with the service...
Hi, I want to send Door Lock Event Notification commands.
so I modified ZB_ZCL_DOOR_LOCK_SEND_LOCK_DOOR_RES macro in zb_zcl_door_lock.h file.
The result...
hello,
i added scan_rsp_data to add a name on my beacon, but now i cant see manufacturer data on the ble_gap_evt_adv_report_t structure but i can see that perfectly on my...
I'm seeing the modulated output of %XRFTEST offset by approx. 1.675 MHz from the set frequency. Modem version is v1.2.2
Here's my command:
AT%XRFTEST=1,1,1,19500,23...
Hi!
Looking at the schematics for the nRF52833 reference circuitry I see that when USB is used, the VBUS is connected to the C18 capacitor, then GND, and if USB isn't...
I have programmed my device with ble_app_rscs available on nRF5_SDK_15.3.0_59ac345. I was expecting it the main loop
the device will only consume 2 uA however it is consuming...
After a few configuration issues we have finally got a connection with the asset tracker application. However we are not getting far enough to send data.
The log shows a...
Hello,
i am trying the nrfsniffer 3.0, but all the packets seems to being dropped.
I am using:
* BLE400 with nrf51822 module (firmware flashed with stlink )
* Linux...
I am trying to make couple templates for S113 with nRF52832 and nRF52840 with and without FreeRTOS and because there is no such in the examples, I’m not sure I made it right...
Hello,
I'm using SDK for Thread and Zigbee v4.1 and I developed a network using mqtt-sn library. Since the developed application requires data publishing at a high rate...
I want to get logs via RTT (JTAG) in the connectivity firmware example of SDKV15.
I have built the connectivity firmware project using cmake and opened the project in SES...
