I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
HI,
I find that the DFU code start address regsiter is different between SDK15.3 and SDK16
SDK15.3
MemorySegment name="uicr_bootloader_start_address" start="0x00000FF8...
Hi,
I'm using the Home Automation profile of the Zigbee protocol and, in particular, I'm developing the Window Covering Device, present in the SDK "nRF5_SDK_for_Thread_and_Zigbee_v3...
It appears the softdevice gets into a strange state when a BLE connection is lost while transferring data. How does application code reset or reinitialize the softdevice ...
Hello,
On the documentation page for nRF5 SDK for Mesh ( https://www.nordicsemi.com/Software-and-tools/Software/nRF5-SDK-for-Mesh ) it says that only the nRF52832 and nRF52840...
Hello,
I'm seeking some clarification on a few points to determine the performance of the nRF52840 in high density deployments. The current intended soft device is S140...
Hello,
in the current project we use a large array (16kB) in RAM to store data. After a reset we would like to check if the array is not corrupted to continue processing...
Dears,
I'm using nrf52832 with PCA10040 and SDK 16.0.0,I want to make a DFU via uart. So used the firmware provided in the SDK(nRF5_SDK_16.0.0_98a08e2\examples\dfu\secure_dfu_test_images...
Hello,
I would like to evaluate nRF9160 for incoming project.
I have Nordic Thingy:91 with iBasis sim card.
Unfortunately, during configuration it turned out, that...
Hi,
We are using nRF9160 for our application and need to design power supply with battery management IC for it and need to know how much power it will consume with all...
Hi,
I would like to setup my nRF52840-Preview-DK as a central to communicate with a peripheral device via UART over BLE.
Once my peripheral device is connected it writes...
I try to connect NRF9160 dev kit to LTE/NBIOT. But device cannot connect to the LTE/NBIOT network. I am using the at_client example with nRFconnect v3.3.0 LTE link monitor...
I have successfully managed to both provision and configure the simple:_on_of_client.
but i'm having troubles configuring the simple_on_off server. I really have no idea...
Hi folks,
I need of your help. I've developed a new custom board with the nrf52840 CKAA ball assignment and I'm having problems on programming it.
I've developed my...
I am getting errors when initializing the Peer Manager in my code. Here are the items that are unique to my setup:
1) I have a thread which uses fstorage to store a single...
