Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
I need to run gc because I get rc =FDS_ERR_NO_SPACE_IN_FLASH.
So I run gc simple as written in https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.3.0...
Hi all
we used a nrf52832 to communicate over SPI and I2C at the same time with some sensors. This works fine.
At the moment I try to convert the project to nrf52810 but...
Hello,
does anybody now when the sniffer will support coded PHY?
I found a similar questions but no answer yet...
https://devzone.nordicsemi.com/f/nordic-q-a/42216/does...
Hi,
I would like to combine NFC - BLE pairing and launch app record. Naively I thought I would write the second data right after the first:
But this does not work. Reader...
I am using an NRF52832 on an energy harvesting board where lowest power is critical. I can achieve ~2 uA current consumption in idle state (waiting on RTC interrupt), wake...
Hi,
I work on the nRF52840 DK with the ble_app_uart example and I want to add a timer using app_timer api,
in order to create RTC time/date timestamps for my sensors raw...
Hello
I am using SDK15.3 and nrf52832 development board.
In my setup,
1. I have a few peripheral nodes whose only job is to transmit some arbitrary packets ( say P)...
My setup consists of a Raspberry pi and a PCA10056 dev-board (NRF52840). I followed the instruction from here in order to set up the Raspberry pi as boarder router and connect...
Hi all,
I am working on the Smart remote and when "spamming" a lot of key simultaneously, I sometimes get a warning "m_coms : packet lost" and then a disconnection.
...
Hello,
I have a Taiyo Yuden EYSHSNZWZ module. I also had a breakout board manufactured for it to get access to all the pins. I am having trouble trying to program the...
Hello,
I`m trying to get this ( https://github.com/NordicPlayground/nrf52-ble-multi-link-multi-role/ ) working properly to test the possible working range between two nRF52840...
To the kind attention of the Nordic support team,
Hi to you all, I have got legacy gazell code running on nRF24. In old code the following instructions was used:
hal_nrf_set_address...
My customer wants to do a range test with a propritary 802.15.4 software.
Do you have an example for the nRF52840DK with an blinking led if the communication is established...
Hello,
i want to display a string in 5x21 led matrix using HT1632 Led driver
Using SPIM0 Protocol i should send data from nrf52832 to HT1632 led driver
My question is...
